Key Responsibilities:

• Development of Analog/Mixed-Signal circuits from specifications to prototypes.
• System-level analysis and evaluation, full-chip architecture design, analysis, modeling, simulation, and integration.
• Schematic entry, corner simulation, layout consideration, and post-layout simulation.
• Work closely with the layout engineer to conduct the physical implementation (layout) and chip floor planning.
• Responsible for post-layout extraction and parasitic analysis.
• Able to work with other designers, Chip Architects, and layout engineers to achieve full-chip integration, place and route, top-level verification, and tape out.

Requirements:

• Ph.D./Master/Degree in Electrical Engineering or Microelectronics with excellent technical background in Analog /Mixed-Signal IC design
• Min. 3 years of experience in CMOS Analog IC design and simulation
• Good design experience in Analog IC design involving two or more of the following blocks: low noise pre-amplifier (low offset, high CMRR, high PSRR and bandwidth up to 600MHz), CMOS Gigahertz Oscillator, switched capacitor circuit, LDO, Differential Amplifier, comparator, Opamp, TIA, and Bandgap Reference and high-frequency full-wave rectifier, etc.
• Good design knowledge in ESD and Latch-Up.
• Experience in isolator devices (capacitive-coupler or optical-coupler) and photodetector-associated circuits will be an added advantage.
• Experience with sigma-delta modulators and IO drivers will be an added advantage.
• Good working knowledge of relevant analog IC design and simulation tools (Spice or its equivalent)
• Basic understanding and can develop simple design-related scripts with some common script languages, such as perl, Tcl, matlab or cadence skill etc.
• A team player with good communication skills.
• Able to work independently, flexibly, and creatively.
• Candidates with no prior working experience are welcome to apply.

Key Responsibilities:

• Development of Analog/Mixed-Signal circuits from specifications to prototypes.
• System-Level analysis and evaluation, full-chip architecture design, analysis, modeling, simulation, and integration.
• Schematic entry, corner simulation, layout consideration, and post-layout simulation.
• Work closely with the layout engineer to conduct the physical implementation (layout) and chip floor planning.
• Responsible for post-layout extraction and parasitic analysis.
• Able to work with other designers, Chip Architects, and layout engineers to achieve full-chip integration, place and route, top-level verification, and tape out.

Requirements:

• Ph.D/Master/Degree in Electrical Engineering or Microelectronics with excellent technical background in Analog /Mixed-Signal IC design.
• Min. 5 years of experience in CMOS Analog IC design and simulation.
• Good design experience in Analog IC design involving two or more of the following blocks: low noise pre-amplifier (low offset, high CMRR, high PSRR and bandwidth up to 600MHz), CMOS Gigahertz Oscillator, switched capacitor circuit, LDO, Differential Amplifier, comparator, Opamp, TIA, and Bandgap Reference and high-frequency full-wave rectifier, etc.
• Good design knowledge in ESD and Latch-Up.
• Experience in isolator devices (capacitive-coupler or optical-coupler) and photodetector-associated circuits will be an added advantage.
• Experience with sigma-delta modulators and IO drivers will be an added advantage.
• Good working knowledge of relevant analog IC design and simulation tools (Spice or its equivalent).
• Basic understanding and can develop simple design-related scripts with some common script languages, such as perl, Tcl, matlab or cadence skill etc.
• A team player with good communication skills.
• Able to work independently, flexibly, and creatively.

Key Responsibilities:

• Development of Analog/Mixed-Signal circuits from specifications to prototypes.
• System-level analysis and evaluation, full-chip architecture design, analysis, modeling, simulation, and integration.
• Schematic entry, corner simulation, layout consideration, and post-layout simulation.
• Work closely with the layout engineer to conduct the physical implementation (layout) and chip floor planning.
• Responsible for post-layout extraction and parasitic analysis.
• Able to work with other designers, Chip Architects, and layout engineers to achieve full-chip integration, place and route, top-level verification, and tape out.

Requirements:

• Ph.D/Master/Degree in Electrical Engineering or Microelectronics with excellent technical background in Analog /Mixed-Signal IC design
• Min. 8 years of experience in CMOS Analog IC design and simulation
• Good design experience in Analog IC design involving two or more of the following blocks: low noise pre-amplifier (low offset, high CMRR, high PSRR and bandwidth up to 600MHz), CMOS Gigahertz Oscillator, switched capacitor circuit, LDO, Differential Amplifier, comparator, Opamp, TIA, and Bandgap Reference and high-frequency full-wave rectifier, etc.
• Good design knowledge in ESD and Latch-Up.
• Experience in isolator devices (capacitive-coupler or optical-coupler) and photodetector-associated circuits will be an added advantage.
• Experience with sigma-delta modulators and IO drivers will be an added advantage.
• Good working knowledge of relevant analog IC design and simulation tools (Spice or its equivalent)
• Basic understanding and can develop simple design-related scripts with some common script languages, such as perl, Tcl, matlab or cadence skill etc.
• A team player with good communication skills.
• Able to work independently, flexibly, and creatively.

Architecture / Interior Design, Building and Construction, Design, Engineering, General Management, Manage the Project, Prepare the Auto Cad drawing for New projects and upgrading works to Submit Clints when necessary, manage the Project. Manage the employees, Prepare Tender and Quotations when necessary. Monitor Project, Attend Meeting, arrange Meeting ect. Monitor clients and Project. Assist the Project when necessary. Work with Team works ect.

(A) Essential Job Functions:

The Design Engineer (C&S) is responsible, but not limited to, the following:

• Coordination of civil/structural works for construction.
• To attend meetings with client, subcontractors and consultants, etc.
• Attend to site issues, ensuring timely response of RFI, coordinate CO substantiations, material costing and estimation.
• Liaise closely with internal and external parties as well as the authorities to resolve structural design discrepancies and construction issues.
• Coordinate with consultants an liaise with authorities for updates and submissions of project design.
• Manage and resolve production, quality, design & engineering and schedule issues.
• Liaise and coordinate with other stakeholders and consultants on the design and technical issues relating to temporary works.
• Any ad-hoc duties assigned by supervisor.

(B) Minimum Qualifications/ Job Experience:

• Minimum Degree holder in Civil/Structural Engineering or Geotechnical Engineering or its equivalent.
• At least 3 years of engineering experience in the Construction industry.

(C) Knowledge/ Skills/ Abilities:

• Working knowledge of general construction knowledge, especially in Civil Projects.
• Good verbal and written communication skills.
• Strong organizational and interpersonal skills.
• Strong time management skills with exceptional attention to detail and ability to manage multiple tasks/projects at one time.
• Ability to analyse and synthesize complex issues quickly.
• Able to work overtime and be on standby when required.

• Machine design in Mechanical aspect
• Perform mechanical part detailing
• BOM & machine manual writing
• Conduct machine acceptance with customer
• Co-ordination with sub-contractors for machine build
• Posses strong leadership quality and be self-motivated
• Experience in Solidwork 3D software to do mechanical design
• Good knowledge and experience in machine automation
• Degree / Diploma in Mechanical Engineering

Job Description:

- Perform Civil, Structural Analysis and Design to meet project specifications

- Coordination and Liaise with Clients, Authority and Other Consultants, Contractors on Projects

- Ensuring Good Project Documentation and Submission to Authority and Clients

- Attend Project Meeting and Perform Inspections on Designed Works

- To Lead and Mentor Junior Engineer in Performing Engineering Task

- Reporting to Principal Engineer / Management

Job Requirements:

- Candidate must possess at least a Master's Degree /Bachelor's Degree / Post-Graduate Diploma / Professional Degree in Engineering (Civil/ Structural) or equivalent, recognized by Professional Engineering Board of Singapore

- At least 4 Year (s) of working experience in the related field is required for this position

- Good Working Attitude, Self-Motivated, Positive Thinking, Independent, Discipline, Attention to Details and Ownership of Tasks

- Familiar with Local Design Standard and Code

- Knowledge of Design Software, e.g., STAAD Pro, Plaxis, AutoCAD will be added advantage

JOB DESCRIPTION

· Work on SoC architecture discussion and optimization with architect; SoC integration; system block development, e.g., power management, clock/reset, system register, test control, PinMux, etc;

· Work on SoC floorplan with architect and APR; SoC power check; SoC timing constraints and review support; SoC DFT support; SoC verification plan and SoC verification support

JOB REQUIREMENTS

· Bachelor’s or Master’s Degree in Electronic Engineering with ASIC design experience.

· Experience with ASIC design flow

· Experience in RTL coding, RTL and gate-level simulation, logic synthesis, static timing analysis, timing closure and verification

· Good understanding of DFT

· Familiar with UNIX/ Linux environment and scripting

· Good communication and interpersonal skills

· Strong analytical and problem-solving skills

• Identify requirements and features for semiconductor equipment and create concepts and architecture of new equipment.
• Design mechanical systems which involve the selection and use of motors, actuators, gear drives, pumps, and valves.
• Responsible for design verification and validation testing to ensure compliance with specifications, safety regulations and product requirements.
• Create a detailed Mechanical drawing and apply analysis tools like Fish Bone Diagram and FMEA.

Requirements:

• Degree in Mechanical Engineering or equivalent
• At least 5 years of experience in Die Sorter.
• Familiar with 3D CAD software.

If you are keen to apply for the position, kindly email your detailed resume in MS Word to [email protected]

Please note that only shortlisted candidates will be notified.

For more job opportunities, please visit our website at www.recruit-expert.com

EA Licence: 19C9701
Registration: R21100996

JOB DESCRIPTION

In this position, the individual thoroughly understands digital design specs of various IP blocks and SoC architecture definition

• Develop detailed module level and SoC level testplans for all the functional features, based on the design spec.

• Develop ASIC verification environment including all the respective components such as stimulus, checkers, assertions, monitors and scoreboards.

• Develop directed and constrain-random verification functional tests and simulate using EDA tools to verify functional spec is working

• Execute verification plans, including design bring-up, DV bring-up, regression enabling for all the features.

• Collaborate with digital design team to debug functional testcases and deliver functionally correct designs

The ideal individual must have proven ability to achieve results in a fast moving, dynamic environment

JOB REQUIREMENTS

· BSEE or MSEE, entry level

· Strong communication, analytical and documentation skills and ability to interface with other groups

· Strong VLSI functional verification experience, preferably with exposure to complex, high speed custom VLSI products

· Strong hardware functional verification language and Object-oriental language development skill. Prefer with SystemVerilog/ UVM experience

· Familiar with ASIC verification methodology, tools, and development flow

· Working experience or familiar with Ethernet L2/L3 switch/router, SOC, AMBA bus, high-speed IO (USB-2/3, PCIe gen2/3, SATA), Flash controller, or CPU peripherals

Senior/Process Design Engineer (Wastewater Treatment)

Our client is a leading environmental solutions firm with strong expertise in EPCC, O&M and design & build. In line with their growth and expansion, they’re now looking for a Senior/Process Engineer to join their dynamic organization during an exciting time in their development.

Job Responsibilities

• Be responsible for designing, implementing, and optimizing wastewater treatment processes and systems
• Coordinate with cross-functional teams, including design, construction, and commissioning, to ensure seamless project execution.
• Prepare technical specifications for treatment plant
• Provide engineering support for tender activities, bids and proposals, and prepare testing and commissioning plans
• Manage contractors and suppliers, ensuring adherence to technical specifications and safety regulations
• Lead continuous improvement initiatives to enhance the reliability and effectiveness of wastewater systems.
• Ensure that treatment plants comply with regulatory standards and operate efficiently

Requirements

• Minimum Degree in Chemical Engineering, Environmental Engineering or related field
• Possess process/mechanical design experience with wastewater treatment projects
• Must be willing to be hands-on to be on site occasionally
• Must be able to draw and review drawings (i.e. create process flow diagrams (PFDs), piping and instrumentation drawings (P&IDs), perform detailed calculations related to plant process design)

Location: West

Interested candidates kindly forward your CV to [email protected] (Tan Yi Ling, Reg No: R21103172). You may email this great opportunity to someone who would be a great fit for this role.

All information will be kept strictly confidential. We regret to inform that only successful applicants will be contacted.

PeopleSearch Pte Ltd

EA License No: 16S8057

Senior Design Engineer
5 days
9am-6pm
Kallang
Up to $7000

Responsibilities:

• Define requirements and features for semiconductor equipment
• Develop concepts and architecture of new equipment
• Design mechanical systems which involve the selection and use of motors, actuators, gear drives, pumps and valves.
• Produce detailed engineering drawings
• Perform design verification and validation testing to ensure compliance with specifications, safety regulations and product requirements.
• Improve design of legacy machines
• Application of analysis tools like Fish Bone Diagram, FMEA etc.

Requirements:

• Degree in Mechanical or Mechatronics Engineering
• More than 5 years of experience in semiconductor equipment design
• Good knowledge and experience in the following areas :
  1) Design of automation or semiconductor equipment
  2) High precision machine design
  3) Design of High Speed Pick and Place mechanisms
• Familiar with 3D CAD software
• Ability to plan, prioritize, and coordinate throughout the project cycle
• Equipment troubleshooting skills
• Ability to produce detailed Mechanical drawings and apply knowledge of Geometric Dimensioning & Tolerancing.

WhatsApp: +65 9837 8400

Lim Jun Yao Reg No.: R1989028

The Supreme HR Advisory Pte Ltd EA No.: 14C7279

Responsibilities:

• Work closely with design engineers and architects to create and document detailed test plans for verifying the SoC design.
• Establish and manage the infrastructure and environment for automated verification of the SoC's architecture, functionality, and performance.
• Develop reusable testbenches, test cases using constrained-random and directed methods, and verification modules for both block and system levels.
• Create a regression strategy, methodology, and scripting tools, ensuring comprehensive function coverage and addressing verification gaps before design releases and tape-out.
• Collaborate with design engineers to troubleshoot and resolve simulation issues.
• Provide support to test engineers during post-silicon validation.
• Mentor and guide team members and junior engineers, aiming to enhance verification efficiency.​

Requirements:

• Master in Electrical Engineering or equivalent with 8 years of relevant working experience/ PhD in Electrical Engineering or equivalent with 3 years working experience.
• Extensive understanding of UVM/OVM, Semiformal Verification, assertion-based verification, and hardware-software co-verification methodology.
• Skilled in Verilog, SystemVerilog, Python, Perl, TCL, Shell scripting, C/C++, SystemC, and assembly coding for industry-standard ISAs.
• Familiar with MIPI, AMBA (APB/AHB/AXI) bus protocols, RISC-V/ARM, or DSP cores.
• Experience in verifying designs at RTL and post-P&R gate levels.

__________________________________________________________

HOW TO APPLY :

Interested candidates, please submit your resume by clicking on “Quick Apply” or contact [email protected] for more details.

Please provide following information in the resume for immediate processing

1) Reasons for leaving current and/or last employment

2) Last drawn and/or current salary

3) Expected salary

4) Date of availability and/or Notice Period

All applications will be treated in strictest confidence and only shortlisted candidates will be notified

Wee Wai Dan

EA License No : 03C5391

EA Reg No : R22109628

Note: This role will require travel and based in China and Vietnam for at least 10 months per year. Proficiency in Mandarin is essential for effective communication with Chinese-speaking clients and stakeholders.

Job Summary:

• We are seeking a talented Senior Design Quality Engineer (DQE) to lead quality initiatives for our thermal cooling solutions within the electronics and computing industry. The ideal candidate will be responsible for ensuring design and process quality while driving continuous improvements to achieve product excellence. If you are passionate about quality control, process optimization, and collaborating across functions, we encourage you to apply.

Key Responsibilities:

• Implement advanced monitoring systems to enhance product quality and yield. Identify areas for improvement and lead initiatives to optimize production processes.
• Take charge of addressing and improving abnormal quality issues in manufacturing processes. Collaborate with cross-functional teams to implement effective solutions and preventive measures.
• Strengthen internal quality control processes and improve overall capabilities, particularly in mechanical processes such as metal stamping, forging, brazing, die casting, CNC machining, and milling. Drive initiatives aimed at maximizing operational efficiency.
• Lead corrective actions for customer-reported quality issues and communicate preventive solutions to relevant stakeholders.
• Streamline quality inspection planning by integrating automation and advanced technologies whenever possible.
• Promote effective communication and coordination with design, production, and other teams to ensure adherence to quality standards.
• Manage task assignments, performance, and development of the quality team, ensuring timely completion of deliverables.

Requirements:

• Bachelor’s degree in Mechanical Engineering, Industrial Engineering, Quality Engineering, or a related field.
• Minimum of 5-7 years of experience in quality engineering, particularly in manufacturing and design quality.
• Proven experience in mechanical processes, including metal stamping, forging, brazing, die casting, CNC machining, milling, and knowledge of tooling and the design/manufacture of fixtures and jigs.
• Strong analytical, problem-solving, and leadership abilities.
• Familiarity with quality management systems and standards.
• Six Sigma certification or equivalent is a plus.
• Willingness to travel frequently and work abroad in China and Vietnam for at least 10 months per year (includes four round-trip tickets to Singapore annually and separate arrangements for living accommodations).

Job Highlights

• Opportunities to work on award-winning projects
• Performance bonus for high-performer
• Good medical benefits

Job Description

Your Role

• Prepare and compile costing for building and interior works
• Attend all design consultations and site meetings
• Prepare high standards of 3D and AutoCAD Drawings, Material Boards
• Prepare schedule of finishes and project management schedules
• Brief and explain to contractors the proposed design intents and finishes
• Ensure quality and a high level of customer satisfaction

Job Requirements

• Experience in designing residential and hospitality projects
• Must possess skills in the following Computer-Aided Software Skills: Autodesk AutoCAD & Adobe Photoshop
• It is good to have the following skillset in Autodesk 3D Max, SketchUp, Vray
• Highly motivated, confident, and eloquent with good interpersonal skills
• Good communication skills
• Computer proficiency in Microsoft Office – Excel, Word, PowerPoint, etc

Perks/Benefits

• Opportunities to work on award-winning projects
• Performance bonus for high-performer
• Good medical benefits
• Friendly Working Environment
• Good Career Growth

Interested candidates, please send your resume and portfolio to [email protected].

Job Description

• Assist the Architect to coordinate design detailing between Clients and Consultants
• Coordinate all architectural drawings and works, submit and update status of shop drawings, samples,
• mockup, and materials as well as supervise work progress to alleviate conflicts, dispute and abortive work
• Review project specifications, tender clarifications and construction drawings for contract and procurement
• management
• Ensure compliance with architecutral specifications and achieve quality aspect of architectural works without
• deviation to authority requirements
• Responsible to the project stakeholders for accomplishing the project objectives within the constraints such
• as project scope, time, cost and quality of the project.
• Prepare any necessary construction method statement and technical proposal to ensure smooth transition of
• works
• To coordinate architectural work, prepare estimates, interpret plans and inspect construction sites
• To coordinate architectural and consultant drawings to ensure consistency in construction documents
• Resolve all site architectural issues (i.e. drawings discrepancies, method statements or correspondences) and
• implement the right methods to ensure quality and productivity, using BIM software or equivalent
• To liaise with client, consultant and specialist subcontractors for project execution if required
• Arrange and attend joint site inspections with all system wide and in-house contractors if required
• Review and report on the progress of architectural works
• Liaise and work closely with the civil construction team and follow the construction progress closely
• Assist in ensuring that all architectural construction requirements are incorporated into the site construction
• To assist in construction administration process by attending site visits if required
• Compile and handover of architectural documentations including as-built drawing submissions
• To ensure the project complies with regulations, which includes revising the project design as necessary to
• achieve client satisfaction
• Adhere to safety and health regulations and aim for zero accident in the workplace
• Ensure safety and housekeeping is to maintained to the highest standard
• Any other ad-hoc duties as and when assigned

Job Requirements

• Degree in Architecture, and as a registered architect, with minimum 4 years of local working experience OR
• Diploma in Architecture with minimum 5 years of local working experience
• Proficient in project management and architectural trades
• Proficient in trades coordination via Revit/Bentley platform
• Eye for details in architectural shop drawings
• Excellent team player, good interpersonal skills and a “can-do” attitude
• Ability to multi-task in a fast paced and dynamic environment
• Completed min 2 CONQUAS building project
• Preferably with Design & Build Building experience

As the Marketing & Design Intern, you will be assisting the Communications Director in developing content and doing market research for a new business.

You will be assisting in:

- Social Media management

- Designing and development of content using Canva

- Website editing

- Learning Management System management (on TalentLMS.com)

You must:

- Have an eye for detail

- Have good written and/or spoken English

- Be able to do market research and present findings

- Be able to work independently

- IT-savvy is a plus

If you are trustworthy, efficient, and able to work independently, there are opportunities to work flexibly and on independent projects.

NO experience needed. FRESH GRADS WELCOME :)

Job Description & Requirements

1. Design Direction and Presentation:

a. Provide design guidance, creative direction, and innovative proposal to meet client requirements.

b. Present and effectively communicate design intent during client pitches and project discussions.

2. Client Management:

a. Efficiently handle multiple projects concurrently, overseeing them from start to finish, including sales, design, and execution phases.

b. Ensure that projects are completed on time and meet client expectations.

3. Design Implementation:

a. Conceptual design for pitching projects, including mood board, rendering.

b. Translate design concepts into detailed plans, ensuring that aesthetic intent aligns with technical feasibility.

c. Collaborate with design principal, and clients, qualified Persons and vendors to refine and finalize design details.

d. Collaborate with MEP engineers to ensure the seamless integration of mechanical, electrical, and plumbing systems within the interior design.

e. Produce comprehensive construction drawings, including floor plans, elevations, sections, and details, with a focus on precision and clarity.

4. Building Management Submissions:

a. Prepare and submit drawing package required for approvals from building management.

b. Coordinate with QP for submission to relevant authorities.

c. Manage the submission process, tracking progress, and ensuring timely approvals.

5. Project Design Coordination:

a. Coordinate with project teams to integrate architectural, structural, MEP, and interior design elements seamlessly.

b. Coordinate with procurement team to select feasible materials for design implementation.

c. Collaborate with Project Leaders from project initiation to completion, offering design expertise and insights.

d. Attend adhoc meetings related to design and project matters, including client meetings, project meetings, and site visits.

e. Monitor the implementation of design intent on-site and provide guidance or recommend design changes as necessary.

6. As-Built Submissions:

a. Ensure that all design changes and solutions are seamlessly integrated into project documentation.

b. Oversee the creation of accurate as-built drawings, reflecting the final state of the project post-construction.

c. Ensure that as-built submissions are complete and comply with relevant industry standards.

Requirements:

1. A recognized Degree/Diploma in Interior Design or an equivalent qualification.

2. Proficiency in a range of design-related software, including Hand Sketch, Sketchup, AutoCAD, and similar tools.

3. A minimum of 5 years of relevant experience in commercial design, showcasing strong technical knowledge in areas such as shop drawings, site surveys, and detail drawings.

4. Proven experience in managing projects from start to finish, encompassing sales, design, and execution.

5. Exceptional flair for creative design and a meticulous eye for design details.

6. Highly proactive with outstanding coordination and execution skills.

7. A collaborative team player with excellent communication abilities.

8. Demonstrated ability to meet and exceed expectations while adhering to tight deadlines.

9. Willing to travel overseas

• Proficient in AutoCAD, PhotoShop and Sketchup, Enscape or VRay.
• Experience in design development, tender, specification and construction drawings.
• Excellent interpersonal and communication skills, self-motivated, hardworking, meticulous willing to work independently and as a team.
• Project Site Experience.

Requirements:

2-4 years relevant working experience.

Diploma/ Degree in Architecture or related field.

Responsibilities:

• Lead/Manage the project team to complete projects on time, on budget and according to client and authority's requirements.
• Manage multiple projects concurrently from design stage to project completion.
• Ensure project team's current workflow practices are in line with company standards and proposed improvements.
• Establish good working relationships with different parties to promote continued partnerships.
• Support the procurement of new business.

The primary role of a Design Manager is to manage all design work required during construction projects. This includes overseeing the production of technical drawings and plans used to build a structure. You ensure that all designs are produced on time and to a high quality and that they are coordinated with the work of architects, engineers and technicians. You also oversee the design process using technical expertise to ensure that designs meet the client’s expectations.

all designs are reviewed with health and safety in mind. You work closely with the design team to identify any potential risks and hazards and ensure that they are addressed in the design process. You also ensure that all designs meet all relevant health and safety regulations and standards.

Design Manager, you will need a related subject, such as architecture, construction management, construction project management, design management, or architectural technology.

Requirements:

• must possess technical skills and knowledge in construction design and project management.
• knowledge of design software, such as AutoCAD and BIM
• familiar with construction drawings and specifications.
• knowledge of construction materials and methods, building codes and regulations, and sustainability standards.
• excellent analytical thinking skills, be able to think critically and solve problems.
• possess strong leadership and motivational skills to manage the design team and ensure that projects are completed successfully.

A Design Project Manager in Singapore is responsible for overseeing and coordinating design projects from initiation through to completion, ensuring that design processes meet client requirements, timelines, budgets, and quality standards. This role often involves managing teams of designers, architects, engineers, and other specialists while working closely with clients and stakeholders.

Here are the key duties and responsibilities of a Design Project Manager in Singapore:

1. Project Planning and Strategy:

• Define project scope: Collaborate with clients and stakeholders to understand and define the project’s objectives, deliverables, and key performance indicators (KPIs).
• Create project timelines: Develop detailed project plans with timelines, milestones, and deadlines.
• Set budgets: Establish project budgets, including resource allocation for design teams, equipment, and materials.
• Manage scope changes: Handle any changes to the project scope and update project plans and budgets accordingly.

2. Team Leadership and Coordination:

• Lead design teams: Manage and supervise multidisciplinary design teams, including architects, designers, engineers, and other professionals.
• Delegate tasks: Assign responsibilities to team members and ensure that they have the resources and guidance needed to meet project goals.
• Monitor progress: Track the progress of design deliverables to ensure timelines and quality standards are met.

3. Client and Stakeholder Communication:

• Client liaison: Maintain regular communication with clients to understand their needs, gather feedback, and ensure the design aligns with client expectations.
• Present designs: Present design concepts, updates, and progress to clients and stakeholders through meetings, reports, and presentations.
• Manage expectations: Ensure that clients' expectations are properly managed and met, addressing any concerns or issues promptly.

4. Design Oversight:

• Design coordination: Oversee the design development process, ensuring the quality and consistency of the design work across all stages of the project.
• Ensure design feasibility: Ensure that the proposed designs are feasible within the given budget, timeline, and technical constraints.
• Maintain design standards: Ensure that designs adhere to relevant industry standards, codes, and regulations in Singapore.
• Approve design changes: Evaluate and approve design modifications, ensuring that they align with the overall project objectives.

5. Budget and Resource Management:

• Resource allocation: Allocate resources (design staff, tools, software, etc.) efficiently to meet project needs.
• Budget management: Track and manage the design budget, ensuring that resources are utilized efficiently without exceeding financial limits.
• Cost optimization: Identify opportunities for cost-saving without compromising the design quality and functionality.

6. Risk Management:

• Identify risks: Identify potential risks associated with the design phase, including delays, cost overruns, or technical challenges.
• Mitigation plans: Develop and implement risk mitigation strategies to minimize the impact of identified risks.
• Problem resolution: Resolve issues related to design, scheduling, or budgeting that may arise during the project lifecycle.

7. Quality Assurance and Control:

• Monitor design quality: Ensure that design outputs meet the required quality standards, as defined by the client, regulations, and industry best practices.
• Conduct reviews: Organize regular design reviews to assess progress, identify any quality issues, and make necessary adjustments.
• Implement feedback: Incorporate feedback from clients, stakeholders, and the project team to improve the design process and outcomes.

8. Contract and Vendor Management:

• Manage contractors: Work with contractors, vendors, and third-party service providers to ensure design requirements are met.
• Negotiate contracts: Oversee the negotiation and management of contracts with suppliers and vendors involved in the design process.
• Vendor coordination: Ensure that external partners, such as consultants or material suppliers, meet the design specifications and project schedules.

9. Compliance and Legal Requirements:

• Adhere to regulations: Ensure that all design processes and outputs comply with Singapore’s legal, environmental, and building regulations.
• Obtain necessary approvals: Ensure that all design documents, plans, and approvals are in line with regulatory requirements and are submitted to the appropriate authorities.

10. Project Reporting and Documentation:

• Progress reporting: Provide regular progress reports to senior management and clients, including updates on design, timelines, and budgets.
• Documentation: Ensure all design documentation is accurately maintained and archived for future reference.
• Post-project review: Conduct post-project evaluations to assess the design process and identify areas for improvement for future projects.

Skills and Qualifications:

• Design Expertise: Strong knowledge of design principles, architecture, and industry-specific design software (AutoCAD, SketchUp, Adobe Creative Suite, etc.).
• Project Management Skills: Ability to manage multiple projects simultaneously, with experience using project management tools (e.g., Microsoft Project, Trello, Jira).
• Leadership and Teamwork: Ability to lead and inspire design teams, and work collaboratively with stakeholders, clients, and contractors.
• Communication Skills: Strong verbal and written communication skills to present design concepts and ideas effectively.
• Problem-Solving Abilities: Ability to solve complex design and project-related issues efficiently.
• Budget Management: Experience in managing budgets, cost estimating, and financial reporting.

1. Responsible for overall planning and coordination of the development work from conceptualization, design in architectural drawings with 3D max, 3D Studio, SketchUp, Photoshopand Auto-Cad, budgeting, scheduling and quality standrards.

2. Coordinate with revelent authorities & owners till project is complete.

3. Site monitoring till project is hand over.

Job Description

• Oversee the entire ICA design process, from concept to implementation, ensuring project is delivered on
• time, within specifications and meeting industrial standards.
• Lead and mentor a team of ICA engineers and ensuring the quality in design work.
• Oversee the development of control logic, CMS programming, HMI interfaces, and Sub-Control systems, ensuring seamless communication and synchronisation of control components.
• Oversee the selection of instrumentation, sensors, and transmitters for accurate data acquisition, measurement, and feedback control.
• Oversee the configuration and deployment of the Control Monitoring System for seamless process control and integration of subsystems.
• Ensure ICA designs adhere to relevant safety standards (such as SIL, IEC 61511) and cybersecurity protocols to mitigate operational risks.
• Collaborate with process team to optimise the processes through intelligent control strategies, adaptive algorithms, and data-driven insights.
• Coordinate validation activities, including factory acceptance testing (FAT) and site acceptance testing (SAT), to ensure systems meet performance criteria.
• Develop RFQ and collaborate with suppliers and vendors to source components, equipment, and systems required for ICA and ensuring they meet quality and performance standards.
• Oversee testing and commissioning of the CMS, coordinating with process team to ensure system operate as intended.
• Ensure clear and consistent communication with project client and consultant throughout the project, providing updates, addressing concerns and managing expectations.
• Manage ICA design budgets, including cost estimation, resource allocation, and cost control.

Requirements

• Min. of Bachelor Degree in Electrical, Process Control & Instrumentation, Automation Engineering or related engineering discipline.
• 15 years of relevant ICA engineering experience in the planning, design, SAT/FAT and construction of major waste to energy, water, wastewater, process plant projects or similar major industrial projects. The Design Lead has robust experience in managing a team of suitably experienced Design Engineers and Technicians and interfacing with Client, Suppliers and Subcontractors.
• Familiar with code of practice and standards in Singapore
• Experience with Revit/AutoCAD Plant 3D preferred & in other related design software/applications.
• Familiar with Microsoft Office Suite.
• Excellent communication skills in English, both verbal and written.
• Willingness to take on responsibility and work overtime to meet deadlines.
• Extensive hands-on experience in designing and implementing complex ICA systems in industrial environments.
• Proficiency in programming languages for PLCs (e.g., ladder logic, structured text) and HMI/DCS systems is advantageous.
• In-depth knowledge of control system architectures, such as DCS and PLC-based systems.
• Familiar with industry standards and protocols (e.g., OPC-UA, Modbus, HART, Profibus, Ethernet/IP).
• Strong understanding of process control theory, PID tuning, and adaptive control strategies.
• Experience with functional safety standards (e.g., IEC 61508, IEC 61511) and cybersecurity best practices.
• Excellent problem-solving and troubleshooting skills for resolving complex technical issues.
• Strong leadership and communication skills to guide technical discussions and collaborate with diverse teams.
• Good technical understanding of water, wastewater and WTE related control system.
• Relevant experience in design and site work for water, wastewater treatment and WTE works.
• Highly motivated and ability to work independently with minimal supervision.
• full time work at Tuas project site

Job Summary:

The Design Executive reports to the Project Manager and is responsible for creating, interfacing and facilitating design drawings throughout projects' life cycles based on contract drawings and latest information as well as facilitate the flow of information between the design team and project team.

Job Description:

• Prepare, manage and facilitate design drawings using BIM and CAD technologies for building construction
• Take charge of all coordination works of structural and architectural interface with main contractor(s) and other trades for cross-team support
• Ensure all models are compatible and BIM data are made available to all project participants
• Collaborate within design team and other relevant departments to ensure all drawings are in order as per design requirements
• Manage design changes and revisions, resolve discrepancies and queries between design and project teams
• Attend site meetings as required
• Any other tasks as may be assigned from time to time

Job Requirements:

• Diploma/Degree in Architectural/Civil/Structural Engineering or equivalent
• Minimum 5 years of related work experience in similar capacity for construction and architecture projects
• Proficient in MS Office, Tekla, Revit, Navisworks and AutoCAD software
• Knowledge of DGN, DWF, IFC and MicroStation
• Knowledge of native formats of BIM authoring or BIM related applications for design reviews
• Fluent in English with good interpersonal skills
• Strong project management and decision-making skills

Roles & Responsibilities

We are looking for a highly experienced and skilled Design Manager with minimum of 8 years of experience. The candidate should have a proven track record of managing design teams on projects for large scale of Design in international background. The Design Manager must be well-versed with project requirements and standards.

Responsibilities:

Ensure designs meet project specifications, client expectations and company standards within a timeline.

Oversee the entire design process, from concept through to detailed design and construction documentation.

Coordinate with multidisciplinary teams, including architects, engineers, and consultants.

Foster a collaborative and productive team environment. Provide mentorship and guidance to junior designers.

Conduct regular meetings and presentations to update the team (and clients if necessary) on project progress and address any concerns.

Ensure client requirements are accurately captured and reflected in the design.

Implement and enforce quality control procedures to ensure the highest standards of design.

Review and approve design documents, drawings, and specifications.

Conduct regular design audits and peer reviews to maintain quality and consistency.

Ensure all designs comply with relevant regulatory requirements and standards. Stay informed about the latest industry trends, technologies, and best practices.

Requirements:

Bachelor’s degree in Civil Engineering, Architecture, or a related field.
Master’s degree is preferred.
Minimum of 8-10 years of relevant experience in civil engineering or architecture. Proven experience in managing design teams on complex projects.
Experience in the design of residential and mixed use developments is preferred. Strong leadership and team management skills.
Excellent communication and interpersonal skills.
Proficiency in design software and tools (e.g., AutoCAD, Revit, BIM).
Strong problem-solving and decision-making abilities.