. QAQC Inspector (Fabrication /Welding)

Responsibilities:

• Preparing or establishing that a welding procedure is available, has been approved as

required by the appropriate authority and is being employed in production.

• Witnessing of welder and procedure approval tests that including of the preparation of test

pieces and destructive tests and verifying compliance with appropriate standards and

specifications.

• Verification that adequate and valid welder approvals are available, and that only approved

welders as required are used in production.

• Interpretation of weld drawings and weld symbols.

• Performing of visual inspection and ensure that all finished goods are checked and approved

prior to any delivery of handover.

• Verification that post weld heat treatment has been conducted in accordance with

specification requirements.

• Appreciation of the factors influencing the formation of weld defects and their acceptability

in relation to the written specification.

• Coordination with QC Inspector (Hull/Structure and Piping) and NDT Coordinator, to verify

and ensure that all finished welds are checked and approved prior to any delivery of

handover.

• Ensure that quality assurance standards and procedures are maintained.

• Ensure that reports that are required are completed accordingly to the project

specifications.

• Liaise with Contractor, Production and Client’s representative to ensure the product is

checked and complied with the project quality plan and specifications.

• Perform any other tasks as may be assigned by the supervisor.

• Ensure compliance to relevant government regulations and company’s quality, safety, health

and environmental (QSHE) policies, practices and procedures at all times.

Requirements:

• Minimum Diploma in Engineering or relevant field of International certification (e.g. AWSCWI or CSWIP 3.1 WI).

• Physically fit since some of tasks require lifting of some equipment.

• A team player with the ability to work independently as well as in a team

• Good communication skills, meticulous, resourceful, able to multi-task

• Computer literary (MS. Office).

1. Manage the team of RTOs, supervision of site set up, earth works, drainage works and reinstatement works

2. Report to Qualified Person

3. Prepare weekly reports and monthly reports.

4. Attend the meeting with client and consultants

5. Report any non-compliances to Qualified Person

6. Ensure the site Safety

Job Description:

- Prepare weekly reports on vehicle repair status.

- Assist in writing meeting minutes to track outstanding issues.

- Conduct team briefings before starting work.

- Coordinate and manage team assignments and vehicle parking allocation.

- Plan and monitor vehicle sequencing and status for operational tasks.

- Provide documentation support to the Operations Leader for work-related needs.

Job Requirements:

- Degree in Engineering (Mechanical, Electrical, Hydraulic, Automotive, Electrical & Electronics, Mechatronics) or a Diploma in a related field with 5 years of relevant industry experience.

- Strong team player.

- Ability to lead a team effectively.

Responsibilities:

• Assist Engineer in coordinating and supervising maintenance and overhauling jobs
• Prepare Job Acceptance on completion of Jobs
• Monitor and update job status daily.
• Supervise mechanical / diesel / air-conditioning works
• Liaise with customers and contractors on works to be carried out
• Arrange for inspection / job acceptance
• Carry out general repair and maintenance jobs onboard vessels or in workshops
• Dismantle and troubleshoot for mechanical defects
• Perform testing of equipment to ensure smooth operation
• Perform test run and report to superior on the job completion status

Requirements:

• NTC in Mechanical/Marine/Automotive related field.
• Physically fit with good eyesight
• Possess basic understanding of basic components and functions of mechanical engines or diesel engines
• Able to use IMTE tools such as micrometer, bore gauge and torque wrench
• Able to read simple drawings and service reports
• Possess man management experience for up to 5 technicians
• Willing to work under outdoor environment on site
• Basic working knowledge in MS Word and Excel for status and reporting purpose
• Willing to work in Changi area, with company transport provided

Other Information:

• Location: Changi
• Transport provided at: Jurong West & East, Jalan Bahar, Choa Chu Kang MRT, Bukit Panjang, Woodlands MRT, Bukit Merah, Sengkang, Pasir Ris MRT, Tampines MRT, Tanah Merah MRT
• 5 days work week
• Working Hours: 7.45am-5pm

Job Responsibilities:

- Perform general administrative duties.

- Assist in accounting tasks (no need experience for full-set accounting).

- Proficient in Excel and willing to learn other accounting software.

Requirements:

- At least 2-3 years of experience in admin and accounting roles.

- Strong communication skills in English

- Singaporean/PR preferred.

If you are detail-oriented, organized, and eager to contribute to a dynamic team, we want to hear from you!

Job Responsibilities:

• Handle full/partial sets company account.
• Monthly account closing and management reporting
• Actively involved in the new ERP system
• Keep track of inventory inflow and outflow
• Ability to handle multiple tasks and prioritize effectively
• Attention to detail and accuracy in documentation.
• Any other ad-hoc duties assigned

Requirements:

• At least 2 to 3 years of relevant working experience
• Knowledge and proficiency in accounting technology software and databases and other business intelligence software.
• Strong attention to detail and accuracy.
• Good organizational and time management skills.
• Ability to work independently and manage tasks efficiently.
• Excellent communication skills.

About our company

We are a leading engineering and construction company based in Singapore. With multifaceted project management capabilities and a strong diverse workforce, we provide a full range of services in engineering, procurement, construction and maintenance of power and industrial plants across the world.

Responsibilities

• Perform inspections and tests on electrical and instrumentation systems, including cables, panels, field instruments, and control systems.
• Ensure installations and testing comply with approved drawings, project specifications, and relevant standards
• Prepare and review Inspection and Test Plans (ITPs), Method Statements, and Quality Control procedures.
• Maintain quality records, such as test reports, calibration certificates, and inspection checklists.
• Liaise with construction team, subcontractors, and corporate QMS department to address quality-related issues
• Support commissioning activities by ensuring all quality requirements are met before system handover
• Ensure compliance with industry standards, local regulations, and safety requirements
• Any other duties to be assigned from time to time

Pre-requsities

• Degree/Diploma in Electrical Engineering or related field
• Minimum 5 years of experience in power or industrial plant construction projects
• In-depth knowledge of electrical systems for critical equipments in power plant construction
• Proficiency in inspection and testing of electrical and instrumentation systems
• Effective communication and interpersonal skills for collaboration with multidisciplinary teams
• Commitment to safety and compliance with regulatory requirements
• Project location: Jurong Island (Transport provided at designated pick-up points)

Key Responsibilities:

AI Model Development: Design, develop, and deploy machine learning models and algorithms to solve complex business problems.

System Maintenance: Monitor and maintain AI systems to ensure optimal performance, reliability, and scalability.

Data Management: Collect, pre-process, and analyze large datasets to train and validate AI models.

Collaboration: Work closely with cross-functional teams, including data scientists, software engineers, and business stakeholder, to integrate AI solutions into existing systems.

Continuous Improvement: Stay updated with the latest advancements in AI and machine learning, and implement best practices to enhance our AI capabilities.

Experience:

• System Integration & Deployment
• System Monitoring and Maintenance
• Software system version control

Knowledge and Skills:

• Programming Languages
• Machine Learning & Deep Learning
• Data Management
• Natural Language Processing
• Computer Vision
• Computer System Monitoring and Maintenance
• Good communication skills, both written and oral
• Team player with the ability to work independently
• Stakeholder Management
• Analytical Skills
• Problem Solving Skills

Education, Qualifications and Special Training

• Educational Background: Bachelor’s or Master’s Degree in Computer Science, Engineering, or a related field.
• Technical Skills: Proficiency in programming languages such as Python, R, or Java. Experience with machine learning frameworks like TensorFlow, PyTorch, or scikit-learn.
• Problem-Solving: Strong analytical and problem-solving skills with the ability to think critically and creatively.
• Communication: Excellent verbal and written communication skills to effectively convey technical concepts to non-technical stakeholders.
• Experience: Prior experience in AI/ML projects, preferably in a corporate setting.

Personality Traits:

• Strong sense of responsibility and task ownership
• Strong communication skills and interpersonal skills
• Strong curiosity about new technologies, management paradigms that are relevant to the company and Marine industry
• Able to work under pressure
• Able to work independently, and with incomplete information

Other Information:

• Location: Benoi Road (Island-wide transport provided)
• 5 days work week
• Working Hours: 7.25am-5pm

About our company

We are a leading engineering and construction company based in Singapore. With multifaceted project management capabilities and a strong diverse workforce, we provide a full range of services in engineering, procurement, construction and maintenance of power and industrial plants across the world.

Responsibilities:

• Oversee the installation, calibration, and testing of instrumentation and control systems
• Conduct functional and performance tests for instrumentation and control systems
• Identify and troubleshoot issues during commissioning and ensure timely resolution
• Collaborate with engineering and construction teams to ensure seamless integration of systems
• Prepare and maintain accurate documentation and reports related to commissioning activities
• Ensure compliance with safety standards and protocols
• Any other duties to be assigned from time to time

Pre-requsites:

• Bachelor's degree in Electrical, Instrumentation, or a related engineering field.
• Minimum 5 years of experience in commissioning instrumentation and control systems in power plant or industrial projects
• Strong knowledge of control systems, instrumentation and DCS
• Excellent troubleshooting and problem-solving skills
• Ability to work in a team environment and communicate effectively
• Project Location: Jurong Island (Transport will be provided at designated pick-up points)

ST Engineering is a global technology, defence and engineering group with offices across Asia, Europe, the Middle East and the U.S., serving customers in more than 100 countries. The Group uses technology and innovation to solve real-world problems and improve lives through its diverse portfolio of businesses across the aerospace, smart city, defence and public security segments. Headquartered in Singapore, ST Engineering ranks among the largest companies listed on the Singapore Exchange.

Join our Cyber Team

We are an industry leader in cybersecurity with over two decades of experience, we deliver a holistic suite of trusted cybersecurity solutions to empower cyber resilience for government and ministries, critical infrastructures, and commercial enterprises. Backed by our indigenous capabilities and deep domain expertise, we offer robust cyber-secure products and services in cryptography, cybersecurity engineering, digital authentication, SCADA protection, audit and compliance. We specialise in the design and build of security operations centres for cybersecurity professionals and provide managed security services to strengthen the cybersecurity posture of our government and enterprise customers.

The Pre-Sales Manager (Cybersecurity) manage the pre-sales team and supports the sales team by providing technical expertise and product demonstrations to potential customers. This role ensures that the cybersecurity products meet customer needs and helps drive sales.

Job Description

• Develop proposal for the tenders/bids.
• Experience in overall design for network and security solutions.
• To prepare and deliver the business value solutions for customers, including proposal writing, presentation, conduct, proof-of-concept to showcase its technical feasibility when necessary.
• Work closely with the product management team to ensure proper customer solution positioning and respond to technical aspects of RFPs/RFIs.
• Arrange technical training for clients and sales teams, and conduct proof of concepts, solution designs, and technical workshops.

Requirements

• At least 3 – 5 years of working experience with knowledge of product pre-sales.
• Preferably having formal experience in pre-sales, post sales, delivery team in a tech industry.
• Familiar in the project methodologies such as Planning, Design, and relevant Technologies
• Excellent written and verbal communication skills to explain complex technical concepts in simple terms.
• Possess in-depth knowledge of current technologies, tools, methodologies and industry trends, Government guidelines.
• Possess relevant professional certification like CISSP would be an added advantage.
• Work Location: Jurong East

Find out more: https://www.stengg.com/cybersecurity

ST Engineering believes in fostering a culture where team members are encouraged to overcome challenges, explore new ideas, and work together to succeed. We value individuals who are determined to push beyond the boundaries, and have a thirst for knowledge, continuous learning, and self-improvement.

Job Description

• Coordinated with client, engineers, technicians and provided necessary support for process and Safety groups
• Electrical and instrumentation installation work, wiring and terminations.
• Preparation of Electrical and instrument QA/QC documents.
• Performing loop check, safety interlock functioning test.
• Performing the site testing and commissioning of field Instruments.
• Perform Instrument construction, testing, commissioning work. Preparation of punch list and ensure all the punch list items are rectified before client Final Acceptance.
• Preparation of Electrical & Instrument Index, Instrument IO lists, Instruments datasheets/specifications against the P&ID for the proper construction activities.
• Attend emergency site issues and response to site within service level of agreement

Requirements:

• Diploma/Degree in Electrical/Electronic Engineering
• Relevant experience in Pharma, oil & Gas industry of at least 8-12 year.
• Possess basic safety & health experience and computer skills
• Resourceful, earnest, good team player, meticulous and responsible
• Self-motivated,able to multitask
• Good communication and interpersonal skills, ability to liaise with all levels of people
• Good knowledge of local industry
• Good fundamentals of electrical safety and area classifications.
• Good knowledge of Ingress Protection and explosion prof equipment.

Job Description:

• Familiar with HVAC offshore / marine regulations and rules, such as, SOLAS, ABS, DNV, NORSOK, ASHRAE, ISO 7547, 8861 etc.
• Preparation of cooling load calculation, ventilation system design, air conditioning design, pressure drop calculation, duct sizing, grille/diffuser sizing, material take off etc.
• Responsible for HVAC equipment sizing and selection.
• Preparation of P&ID, D&ID and ducting layout drawings etc.
• Preparation of electrical single line diagram, cable block diagram, control diagram, termination diagram, electrical load calculation HVAC system logic diagram, HVAC Cable schedule etc.
• Ensure the HVAC system design and equipment selection are compliance with client specification, class regulation and hazardous area classification.
• Submission of HVAC/Architectural Design document and drawings for class approval.
• Technical submission (drawings and document) checking and revision control.
• Preparation of technical specification, technical bid evaluations.
• Interface with other disciplines and provide necessary guidance on HVAC/Architectural installation.
• Technical Clarification with Client and Vendor.
• Involved actively and monitoring the engineering, procurement, construction and commissioning HVAC system and architectural work.
• Raise purchase requisition for the project required consumable and hardware items & sub-contractor works.
• Instruct supervisors/foreman on a day-to-day basis for work progress.
• Liaise with representatives, classification society surveyors and other to comply with inspection requirements.
• Resolve any technical problems or issues faced at work site.
• Monitors progress and instruct supervisors and foreman on safety and quality.
• Maintain the file copy of all latest revision drawings, approved procedures, client site instruction, project specifications, raised AFI and client signed reports for materialreceiving inspection and mechanical works for internal and external audits.
• Prepare Red-Line Mark-up as per site changes and submit to Engineering Dept to prepare as-built.

Job Requirement:

• Diploma/Degree in Mechanical Engineering
• At least 5 year experiences in Bolt Torque and Flange Management in Marine shipyard
• Experience in Marine HVAC installation and testing
• Experience in troubling shooting HVAC system and equipments

Mun Siong Engineering Limited is a market leader in turnkey solutions for the Oil & Gas, Petrochemical, Energy, Pharmaceutical & Power industries for more than half a century.

What we offer

We pride ourselves in championing diversity, inclusion, work-life balance, and harnessing technology for a brighter future. For us, sustainability isn't just a buzzword, but a way of life. We also pride ourselves on being at the forefront of environmental responsibility, integrating eco-friendly equipment and practices into everything.

What you'll be doing

• Responsible for processing monthly payroll, overtime claims, allowances, and staff benefit claims.
• Administration of NS, Maternity, Paternity, and Childcare Claims.
• Tracking of attendance records, leave administration, and statutory claims.
• Work with site administration on payroll matters.
• Ability to churn our payroll and HR data-related reports on a regular basis.
• Ensure all payroll processes are aligned with MOM guidelines and internal policies and procedures.
• Ensure timely processing of monthly salary, CPF, FWL, relevant allowances, and contributions to government agencies

We’re looking for

• Min. Diploma / degree in Human Resources or equivalent.
• Min. 3 years of working experience in processing and managing payroll for exempt and non-exempt employees.
• Preferred proficiency in using Unit4 or Prosoft, Time and Attendance software, and Microsoft Excel.
• Good knowledge of Singapore Employment Act and personal income taxation under IRAS.
• Strong proficiency in Microsoft Office applications – Words, Excel, Powerpoint.
• Meticulous, able to work independently and a fast learner with strong organizational skills.
• Self-motivated and able to work under pressure.

Min Qualifications / Experience :

Bachelor Degree in Mechanical Engineering with minimum 3 years relevant experience

Job Skills Required :

Mechanical design of pressure vessels, heat exchagers & atmospheric storage tanks. Thermal design of heat exchangers is also a required skill.

Familiar with international design codes such as ASME, British, Australian & European Codes, Tema, API650 & etc.

Proficient in design software such as PVELite, NozzlePro, StaadPro & Autocad.

Duties & Responsibilities

The duties and responsibilities are:

a) Responsible for the formulation of schedules and datelines for design and date of submission.

b) Check detailed design and drawings based on relevant codes and client specifications, while ensuring the most cost efficient methods of design are used.

c) Liaise and co-ordinate with Project Department to obtain relevant information for detailed design.

d) Determine the conditions and study all pertaining data thoroughly and accurately for a design. Many different combinations of loadings are possible and the most probable combination of simultaneous load for an economical and safe design is selected.

e) Control and issue all technical documents.

f) Any adhoc project assigned by Design Manager.

Job Descriptions

• Strong swimming and diving skills, with the ability to work comfortably and safely in underwater environments.
• Proficiency in using diving equipment, such as masks, fins, regulators, and buoyancy control devices.
• Knowledge of underwater construction techniques, including welding, cutting, and concrete placement.
• Familiarity with underwater inspection and surveying methods, including the use of cameras, sonar systems, and measurement tools.
• Ability to work effectively in a team and follow instructions from supervisors.
• Excellent problem-solving skills, with the ability to troubleshoot issues that may arise during underwater operations.
• Physical stamina and endurance to perform tasks in demanding underwater conditions.
• Strong attention to detail to accurately document findings and report on underwater inspections.
• Good communication skills to effectively communicate with team members and supervisors.
• Knowledge of safety protocols and regulations related to commercial diving.

Job Requirements

• Valid certification as a Commercial Diver from a recognized training institution.
• Minimum of 2 years of experience in commercial diving operations.
• Proficiency in first aid and CPR.
• Ability to pass a physical fitness test and maintain good overall physical health.
• Familiarity with relevant diving regulations and industry standards.
• Knowledge of underwater construction and maintenance techniques.
• Advanced certifications in specialized diving techniques (e.g., underwater welding, inspection) are a plus.
• Experience operating underwater equipment, such as remotely operated vehicles (ROVs) or underwater cameras, is preferred.
• Valid driver's license with a clean driving record.
• Strong references from previous employers or diving instructors.

· Develope a marketing strategy in accordance with the overall company goals and vision

· Understanding Company Products and doing Market Research to identify specific target groups and implement niche marketing strategies

· Grow the social media community

· Implement and manage a multi-channel marketing strategy

· Grow online marketing partners (digital publications or influencers)

· Copywriting and copy editing - Both internal and external marketing materials

· Create and execute highly engaging, Skills and experience in creative content writing

· Cross-platform social media & marketing campaigns (design, call to action and content)

· Manage content - copywriting & design. Handle content schedule and posting of content

· Experience in attaining PR coverage both online and offline

· Simple research work

· Assisting with ad hoc duties as required

Requirements:

· Social media analytics and ads experience is preferred. Social media management and community managers preferred.

· Exceptional communication skills, both written and verbal. Strong written English is a MUST

· Ability to multitask and meet tight deadlines

• Required load and unload material,etc
• Maintain material movement record
• To comply with LTA road safety and traffic regulation and site safety
• To conduct daily check to ensure vehicle is in good and safe condition/upkeeping of vehicle

Job Requirement:

• Valid class 4 driving license and lorry crane operator
• Preferably able to start work within short notice

Develop a marketing strategy in accordance with the overall company goals and vision

· Understanding Company Products and doing Market Research to identify specific target groups and implement niche marketing strategies

· Grow the social media community

· Implement and manage a multi-channel marketing strategy

· Grow online marketing partners (digital publications or influencers)

· Copywriting and copy editing - Both internal and external marketing materials

· Create and execute highly engaging, Skills and experience in creative content writing

· Cross-platform social media & marketing campaigns (design, call to action and content)

· Manage content - copywriting & design. Handle content schedule and posting of content

· Experience in attaining PR coverage both online and offline

· Simple research work

· Assisting with ad hoc duties as required

Requirements:

· Social media analytics and ads experience is preferred. Social media management and community managers preferred.

· Exceptional communication skills, both written and verbal. Strong written English is a MUST

· Ability to multitask and meet tight deadlines

Job Summary:

Seeking a Sales Manager / Engineer with a civil engineering background and sales experience in construction or building materials. This role involves liaising with consultants, professional engineers, architects, and façade contractors to drive sales and deliver presentations.

Job Responsibilities:

• Develop and execute sales strategies.
• Build relationships with industry professionals.
• Coordinate with the technical team to present aluminum and glass, façade and curtain wall solutions.
• Coordinate with project teams and provide regular sales updates.
• Follow up on claims and payments from clients to ensure timely processing.

Job Requirements:

• Degree in Civil Engineering
• Sales experience in construction / building materials
• Knowledge of façades, curtain walls, and glazing systems is an advantage
• Strong communication and presentation skills

· Possess a valid driver’s license

· At least one year driving experience

· Report to transportation co-ordinator

· Ferry workers to and fro work site

· Transport items/equipment according to assigned schedule

· Collection of items from supplier / vendor

· Maintain vehicle under charge

· Ensure compliance of local traffic regulation

· Perform other duties and responsibilities assigned by supervisor/ manager

Project Engineer will be under Marine service line, the appropriate quality check, the compilation of accurate and customized results reports and other deliverables.

1. Working in workshop and vessels.

2. Good communication skills with Ship Owners and Superintends.

3. Good time Management and work Independently.

4. Attend and manage dealing with vendors, designers, classification, and flag statutory on engineering issues

5. Reviewing technical specification and drawings from designer meeting owner, class, and customer requirements

6. To perform any other duties & Responsibilities assigned by superiors from time to time.

7. Ability to demonstrate and implement cost -saving measures.

8. Ability to lead to manage project operations, schedule and specifications.

Requirements:

- Min 5 Years experience as Marine Industry.

- Proficient in Microsoft office applications: Word, Excel, PowerPoint & Outlook

-Proficient in AutoCAD application

- Able to work OT.

- Excellent coordination skills.

- Able to working at Height.

- Possess positive working attitude

· Develope a marketing strategy in accordance with the overall company goals and vision

· Understanding Company Products and doing Market Research to identify specific target groups and implement niche marketing strategies

· Grow the social media community

· Implement and manage a multi-channel marketing strategy

· Grow online marketing partners (digital publications or influencers)

· Copywriting and copy editing - Both internal and external marketing materials

· Create and execute highly engaging, Skills and experience in creative content writing

· Cross-platform social media & marketing campaigns (design, call to action and content)

· Manage content - copywriting & design. Handle content schedule and posting of content

· Experience in attaining PR coverage both online and offline

· Simple research work

· Assisting with ad hoc duties as required

Requirements:

· Social media analytics and ads experience is preferred. Social media management and community managers preferred.

· Exceptional communication skills, both written and verbal. Strong written English is a MUST

· Ability to multitask and meet tight deadlines

• Posting of recruitment advertisements
• Engagement with both internal and external stakeholders such as employees and vendors, etc
• Manage office sundry purchases
• Payroll administration
• Assists in employment contract renewals
• Coordinate medical arrangement for foreign employees (medical check-ups for work pass, and vaccination)
• Ensure complete, up-to-date, accurate and accessible records are kept for all employees.
• Assists in the co-ordination of social and recreational activities to promote the general welfare of all employees
• Performs HR data entry relating to employee's information, training records, etc.
• Manage and route phone calls appropriately
• Assists in work pass applications and other immigration related work.
• Prepare and submit government bodies and statutory board related surveys.

• In-depth understanding of project specifications, technical details and construction drawings.
• Carry out work scheduling, material requisition planning, project supervision and documentation.
• Carry out construction site building/structural works or activities.
• Liaising with the main-contractor, other construction professionals.
• Coordinating and supervising construction workers.
• Daily inspection of construction activities, temporary site facilities on site with QP(s) and client’s representative.
• Participate in site walks e.g. with authorities, client's project management, site management and subcontractors.

1.Manage store Inventory & handle sales cash.

2.Receive ,distribute and maintain adequate quantities of stock at all times.

3.Maintain optimal stock levels.

4.Maintain stock and consumption records.

5.Check incoming materials for quality against invoices,purchase orders and packing slips or other documents.

6.Make clear notes on the receipt of the items against eash invoice.

7.Keeps and updates records of good received and issued.

8.Complies report of expenditure,and monthly stock report.

9.Perform related duties and responsibilities as assigned.