Dismantle Repair and Reassemble Mechanical Equipment

• Identify potential sources of hazard prior to dismantling.
• Use correct procedures and correct method of dismantling.
• Carry out the correct isolation and disconnection procedure.
• Identified, checked and prepared components.
• Apply appropriate tests and test equipment to ensure reassembly is correct and effective
• Use of Condition Monitoring on Mechanical Equipment
• Adjust instruments to meet the operating specification
• Make adjustments with minimum disruption to any ongoing activities and minimum waste of resources.
• Monitor and record what has been carried out in work history or log.

Diagnose Faults in Mechanical Equipment

• Respond promptly to problems in line with approved procedures.
• Select appropriate tests and diagnostic procedures and apply them methodically.
• Carry out Visual, Close and Detailed inspections on Mechanical equipment.
• Use the results of inspections to determine the appropriate actions to take.
• Record an accurate and full description in the appropriate document history

Monitor and Maintain Pollution Control Measures

• Unplanned discharges to the environment are identified, halted where possible, and reported according to policy, procedure and regulation.
• Relevant PPE is used to deal with unplanned discharges using company procedures
• Equipment, waste or other materials for disposal are dealt with according to the correct procedure.
• Environmental protection and pollution control are enforced effectively with colleagues, subordinates and subcontractors.

Contribute to The Health and Safety of the Working Environment

• Work area within your own responsibility is kept clean and free of hazards.
• Positive action is taken to stop hazards and unsafe behaviours
• Alarms are raised as appropriate and/or acted upon using applied policies and procedures or initiative
• Colleagues and subcontractors are alerted ASAP of any hazards or potentially dangerous changing conditions.
• All potential and actual incidents are reported to the relevant supervisor.
• Emergency response
• See Station Bill. Perform emergency response role.
• Demonstrate competence during Emergency Response Drills and training exercises.

Must have prior Experience in the following,

• Dismantle and reassemble Mechanical Equipment
• Monitor and Maintain the condition of Mechanical Equipment
• Diagnose faults in Mechanical Equipment
• Monitor and Maintain Pollution Control Measures
• Contribute to The Health and Safety of the Working Environment
• Emergency Response Role
• Provide any additional duties as required by the OIM/Unit Spt. and/or HOD to maintain safe and efficient running of the Unit.

Qualifications & Experience

• Proven experience and/or qualified to N/SVQ/HNC/HND in Mechanical Engineering or local equivalent
• 3 yrs experience desired with offshore experience preferred.
• Experience and knowledge of hydrocarbon processing systems and utilities.
• Good experience of Permit to Work, Mechanical Isolation Standards and Risk Assessment.
• Medically fit to offshore International standards such as ENG1 or equivalent.
• Proficient in Written & Spoken English Langauge

Job Description

• To carry out drafting of Excavation Drawings with construction sequence;
• To carry out drafting of building structures drawings;
• To carry out drafting of Erosion Control Measure (ECM) drawings;
• To assist Engineer in the drawings/documentation development and preparation.

Job Requirement

• Proficient in Autocad.
• At least 2-3 years of working experience in C&S and Geotechnical filed (with Consultants experience will be preferred).
• Ability to perform drawings according to engineering design and possess good communication skills.
• Candidates with experience and knowledge in (ECM) drawings, Excavation stage construction drawings will have an added advantage.
• Self-driven and possess positive attitude to learn.

Attention Points:

- Outstanding career growth & development opportunity

- Competitive salary & work benefit package

- Passionate, energetic & innovative work culture

Qualified or interested candidates, please click to apply.

Position type: Permanent

Work location: Tuas South Ave 1

Working hours: Mon to Fri : 0830 hr to 1730 hr

Sat : 0830 hr to 1230 hr (As and when needed)

Gross Monthly Salary Package: $3,200 (can be higher depending on experience), additionally + Commission (no Cap)

Job Descriptions :

• Identify & develop new business opportunities
• Establish new accounts as well as maintaining with existing customers
• Meeting Company objectives and expectations
• Marketing function for new products
• Corresponding with customers on quotations and purchase order related issues
• After Sales service calls

Requirements :

• Diploma in Mechanical or other disciplines (With or without experience)
• Dynamic, outgoing personality and self-motivated
• Able to work independently as well as a team player in a fast paced and pressurized environment
• Class 3 Driving License and possess own vehicle
• Only Singaporeans

Interested Applicants, please send your updated resume to [email protected]

Alternatively, you can call or whatsapp me at +65 8390 9886

Mark Ernest Lim (EA Reg No.: R24123374)

Semiko Recruitment & Consultants Pte Ltd (MOM License No.: 96C4777)

We are hiring for our client, a Fortune 500 Tech Company, an Electrical Engineer/Network Infrastructure Engineer - 12 Months Contract Opportunity (Onsite Singapore)

Job Responsibilities:

• Execute regional space, power, cabling and other infrastructure requirements in support of Edge network requirements, present and future.
• Design/Plan new site electrical/mechanical critical infrastructure for Data Center sites.
• Work with Engineers and design and draw layout of Edge/POP sites floor plans, allocate space assigned to network function, optical, backbone, IP, compute, etc.
• Execute all SOW Engineering design packages related to new or existing edge/pop sites as per Edge and Network Services (ENS) standards.
• Proactively contribute to documentation, automation and processes as they evolve.
• Understand the overall needs of current and future POP infrastructure.
• Guide retrospective reviews of completed projects with teams to incorporate lessons learned into the team's future roadmaps and goals.
• Ensure processes are being followed and all documentation and systems are delivered as per set standards.
• Support site acceptance process for new POP sites.
• Travel to site across states for site survey and evaluation on as per need basis.

MINIMUM QUALIFICATIONS

• 8+ years of electrical engineer work
• Outstanding proficiency with AutoCAD/AutoDesk tools.
• Knowledge of engineering principles of the infrastructure architecture (space line up, air flow, cooling etc.)
• Knowledge of Telecom Central Offices, Data Center, Collocations and Remote Hut environments, to include engineering principles regarding power and other infrastructure.
• Understanding of optical network design, installation and maintenance for service providers or enterprise networks.
• Experience with field-based work in POPs, carrier hotels, data centers, and Central Office environments.
• Technical knowledge of various regional Data Center electrical and cooling configurations, IEC, NEMA standards, AC/DC power, power redundancy scenarios.
• Basic knowledge of optical theory, transport technologies, and the operation of optical transport systems.
• Analytical, interpersonal, and communications experience.
• Experience with communication and directing tasks to vendors/suppliers.
• Demonstrated experience analyzing situations and utilizing troubleshooting experience, systems and tools, and problem solving. Hands on experience on Power related projects is a plus.
• Experience working with limited supervision.
• Time management and organizational experience.
• Experience working in a global team environment.
• Willing to travel, approximately 10 to 30% travel required.

MUST HAVE:

• Knowledge of Telecom Central Offices, Data Center, Collocations and Remote Hut environments, to include engineering principles regarding power and other infrastructure.
• Experience with communication and directing tasks to vendors/suppliers.
• Outstanding proficiency with AutoCAD/AutoDesk tools/BIM 360/Blue Beam.
• Professional Engineer license (PE or local Equivalent) is preferred
• Must have Bachelors in Electrical/Electronics Engineering or Equivalent is preferred.

Responsibilities：

Manage the day to day transportation services

Handling and delivery of goods

Assist on admin and general warehouse duties

Ad hoc jobs assigned by management

Requirements:

Class 4 driving license

Light-Moderate physical work is required

Working days : work Regular hours, 6 working days

Responsibilities:

• Provide 2nd level onsite troubleshooting support in response to escalation from helpdesk to ensure consistently meet customer response / resolution times and objectives based on SLA
• Coordinate with equipment vendors and 3rd part suppliers to resolve issues
• Attend to customer enquiries (through phone and email) and follow-up on outstanding issues closely while ensuring that customers are kept updated on the progress
• Maintain call log database system and ensure all unresolved problems are escalated to the senior engineers
• Participate in adhoc projects when required

Requirements:

• Possess NITEC certification or Diploma in IT or relevant discipline
• Experience in desktop support and good working knowledge in Windows OS, Basic Network experience
• Minimum 2 to 3 years experience in customer support environment will be an added advantage
• Able to work under pressure and independently in a team environment
• Must be able to work in a fast-paced and dynamic environment
• Willing to travel around Singapore to multiple sites
• Able to work on rotating shifts

Key Responsibilities:

• To assist in engineering projects, manufacturing and assembly works.
• To assist in the production, testing and qualification of company products and its peripherals.
• To administer technical documentation (schematics/mechanical drawing/user manuals) for engineering and company projects.
• To provide installation and support for engineering projects, including field services to customer (local & overseas)
• Interact with customers and distributors to resolve technical issues

Skills & Requirements:

• Nitec / Higher Nitec in Electrical/Electronics/Mechatronics Engineering.
• Fresh graduates and/or those with relevant experience in motor control and sensors control are welcome to apply
• Willingness to learn and implement changes to improve work processes.
• Self-motivated and ability to work independently.
• Able to start work immediately or with short notice period.

Job Responsibilities

• Design process and perform process calculations for water, wastewater treatment, air treatment projects.
• Design PFD, P&ID with Auto CAD independently or with the help of drafters.
• Select equipment or propose the parameters for selection of equipment such as pumps, fans.
• Design the layout and section views of the overall treatment system including process treatment units, equipment, and piping and ducting with the help of drafters.
• Prepare other textual documents in process discipline such as control philosophy, datasheets.
• Prepare submissions of the process drawings and textual documents.
• Focus on deliverables and deliver the above-mentioned documents on time.
• Evaluation of technical documents from subcontractors and suppliers.
• Coordinate the works with mechanical engineers, and electrical, control and instrument engineers.
• Provide technical support to sales and project teams.
• Other ad hoc jobs.
• Report to engineering manager.

Job Requirements

• Minimum Qualification: Bachelor degree in environmental, chemical engineering or related engineering
• The candidate should be highly responsible for this role.
• A degree in environmental engineering, chemical engineering, mechanical engineering, or all other process related engineering.
• 3 years above work experience in water, wastewater treatment, or air treatment. Master degree holders with less experience will be considered.
• Experiences in ultrapure water treatment, air treatment scrubbers, and thermal oxidizers are preferred.
• Good writing and communication skills.
• Must be able to communicate effectively in English, proficiency in Mandarin will be added as advantage.

Electrical Engineer (Exp: 3+ years)

Permanent Position

Central, Singapore

Rotating shift work is required.

Key Responsibilities:

• Perform daily, weekly, and monthly maintenance on the PBT system, including testing, inspection, adjustment, and calibration tasks, both at heights and within equipment enclosures
• Maintain, test, and troubleshoot key systems, including:Accelerator systems
  Irradiation devices Patient alignment systems Safety interlock systems
• Monitor the operation of the PBT system and identify areas for performance improvement.
• Adopt and integrate new technology, products, and processes to enhance system functionality.
• Respond promptly to service calls, ensuring timely resolution and customer satisfaction.
• Fulfill work orders, submit reports (including timecards, working reports, and expense reports), and adhere to company and customer procedures.
• Assist with troubleshooting and commissioning activities when necessary.
• Ensure compliance with regulatory standards, including radiation safety regulations, company policies, and applicable laws.
• Work with high-voltage equipment, magnetic fields, and in radiation-prone environments.

Requirements:

• Diploma or higher in Electrical Engineering or a related discipline.
• 3+ years of relevant experience with large-scale electrical systems.
• Strong understanding of electrical systems, particularly in environments involving high-voltage, radiation, and electromagnetic fields.
• Proficient in reading and interpreting engineering documents (e.g., schematics, circuit diagrams, piping diagrams).
• Experience using electronic test and measurement instruments such as DVM, oscilloscopes, and micrometers.
• Capable of working independently as well as collaboratively within cross-functional teams.
• Excellent communication, problem-solving skills, and attention to detail.
• Ability to understand and troubleshoot complex equipment and systems.
• Familiarity with Microsoft Word and Excel.
• Comfortable with working at heights and lifting up to 20 kg repeatedly.
• A customer-focused mindset with a strong sense of teamwork

1 OSS System Implementation and Deployment

• Customer requirements analysis (incl. pre-implementation analysis works, requirements clarifications and solution approval)
• Configuration of the system
• Data modelling
• Data migration and data transformation
• System installation
• Auto discovery & Reconciliation – Integration with NMS’s or Network Elements with use of scripts and API’s to retrieve data from the network
• Service design – implementation of the flows with use of SunVizion API to design service
• Service fulfilment – integration with NMS’s or Network Elements with use of scripts and API’s to activate service
• Integration with other business systems
• Reports preparation
• Delivering trainings to the customer
• Project documentation preparation
• Supporting User Acceptance Tests (including technical negotiations with regards to classifying issues observed during tests and agreeing how they should be addressed) as well as any other tests performed during deployment
• Monitoring of customer satisfaction (user experience)

2 OSS System Support & Maintenance

• First and, in the long term, also the second line of support
• Communication with the third (and initially also the second) support line in Poland, in order to meet the agreed KPI parameters.
• Communication with the customer
• Analysing customer issues
• Solving issues if can be solved locally and transferring issues to remote team with required details if product issue
• Verification of the new versions of the SunVizion product before go live
• New version installation with respecting of the support windows

3 Presales and Business Development Support

• Participation in discussions with potential customers in order to understand their needs and prepare appropriate solutions
• Participation in presentations and workshops to potential customers (including live demonstration of the solution)

Essential Duties and Responsibilities:

1. Quality Assurance and Control:

• Develop, implement, and maintain quality assurance plans, procedures, and control measures.
• Monitor and analyse production processes to detect and resolve quality issues.
• Ensure compliance with relevant regulatory requirements, including FDA, ISO 13485, and other applicable standards.
• Support internal and external audits and regulatory inspections.
• Investigate and resolve product-related issues, deviations, and non-conformities, with the authority to recommend corrective and preventive actions.
• Ensure the non-conformance or quality issue is resolved and complete in a timely manner.
• Participate in new product introductions to ensure quality is built into all products early in their life cycle
• Support validation processes including IQ, OQ, PQ, process validation and test method validation.

2. Process Improvement

• Identify opportunities for process improvements to enhance product quality and manufacturing efficiency.
• Lead and drive QA initiatives across the product areas
• Lead or participate in root cause analysis and corrective action planning.
• Support and drive cost improvement project

3. Customer Interaction:

• Address customer complaints and feedback related to product quality.
• Work closely with customers to understand their quality requirements and ensure that products meet their specifications.
• Communicated on any potential change request of the processes to customer.
• Provide technical support and quality-related information to customers.

4. Documentation and Reporting:

• Maintain comprehensive records of quality control activities, inspection results, and non-conformance reports.
• Prepare and support monthly / annual quality reports to management and other stakeholders.
• Ensure proper documentation and traceability throughout the manufacturing process.

5. Training and Development:

• Train manufacturing staff on quality standards, procedures, and best practices.
• Promote a culture of quality and continuous improvement within the organization.

Education/Experience and Qualifications:

• Degree in Engineering or science, with 2 - 5 years of progressive Quality responsibility, preferably in medical device / pharmaceutical manufacturing.
• Diploma holders in Engineering or science with more than 5 years' experience in Quality are welcomed to apply
• Knowledge of regulatory requirements and quality standards, including FDA regulations and ISO 13485 standards.
• Strong analytical and problem-solving skills, with the ability to troubleshoot complex issues.

Job Description:

• Involvement in the entire software development life cycle including application development, implementation, testing, maintenance, and documentation.
• Responsible for the development, installation, configuration, and customization of Enterprise products and/or software services and cloud platforms.
• Designing and implementing scalable web services, applications, and APIs.
• Perform troubleshooting & debugging software defects.
• Writing, testing clean and secure code to ensure responsiveness and efficiency.
• Staying abreast of latest technologies and work with R&D team on conceptualized design of prototype and Proof-Of-Concept (POC) into eventual solution for end user’s business cases.

Requirements:

• Proficient in one or more back-end programming languages/frameworks such as C++, C#, .NET/.NET Core, Java Spring Boot, or Python.
• Proficient in JavaScript and one or more front-end frameworks such as React or Angular.
• Proficient in Git.
• Knowledge and experience in Relational Databases (e.g., MS SQL, Oracle, PostgreSQL).
• Good understanding of Agile/Waterfall software delivery methodology.
• Able to work independently and as a team.
• Fresh graduates are welcome to apply

Only shortlisted candidates will be notified.

Please email a copy of your detailed resume to [email protected] for immediate processing.

(EA Reg No: 20C0312)

The Career Conversion Programme (CCP) (Train-and-Place with Commitment to Hire) for Advanced Biopharmaceuticals Manufacturing Executives/Professionals is a talent development programme aimed at building the next generation of skilled manpower for Singapore’s Biopharmaceuticals manufacturing industry in anticipation of hiring demand.

The training programme consists of 15 months of local attachment with GSK. Due to the nature of the programme, we can only consider Singapore Citizens and Singapore Permanent Residents. There is no CPF contribution for the programme. For more information, please visit Career Conversion Programmes (CCP) for Individuals.

Role Description:

VS1

This position reports to the Production Manager or the Director of Value Stream and is an integral member of Production Management Team. GSK is committed to an employee-orientated, high performance culture that emphasises process automation, quality compliance and continuous improvement.

Pilot Plant

This position reports to the Associate Director Operations & Risk and is an integral member of Operations & Logistics Management Team. GSK is committed to an employee-orientated, high performance culture that emphasises process automation, quality compliance and continuous improvement.

Trainee to be involved in:

V

• To supervise, execute and monitor the activities within the value stream to ensure reliable and optimal operation of processes, equipment, utility and facility so as to achieve target production levels within the framework of current Good Manufacturing Practice (cGMP), quality, safety, occupational hygiene and environment protection.
• Identify and implement improvement to plant facilities, processes, methods of operations and turnaround, troubleshoot for process and equipment problems to minimize safety and quality risk as well as to ensure greater operational efficiency.
• Lead or support quality or safety related investigation using appropriate problem-solving tool to determine the root causes and implement CAPA to prevent recurrence.
• Conducts audits and investigations, participate in audit preparation and complete identified actions in the assigned work area(s), in order to ensure compliance with GMP and safety requirements.
• Prepare documents relating to manufacturing, plant turnaround, Local Operating Instructions (LOI), Local Standard Operating Procedures (SOP) and training manual to ensure that updated documents exist to support the activities of the operations department, schedule plan orders, and materials assignment. Documentation should comply to Data Integrity requirements and adherence to ALCOA principles.
• Support the Production Manager in new product introduction or plant trials and prepare and complete all necessary documents related to plant trial within the stipulated timeline.

Pilot Plant

• To supervise, execute and monitor the activities within the Jurong Pilot Plant to ensure reliable and optimal operation of processes, equipment, utility and facility so as to achieve target production levels within the framework of current Good Manufacturing Practice (cGMP), quality, safety, occupational hygiene and environment protection.
• Identify and implement improvement to plant facilities, processes, methods of operations and turnaround, troubleshoot for process and equipment problems to minimize safety and quality risk as well as to ensure greater operational efficiency.
• Lead or support quality or safety related investigation using appropriate problem-solving tool to determine the root causes and implement CAPA to prevent recurrence.
• Conducts audits and investigations, participate in audit preparation and complete identified actions in the assigned work area(s), in order to ensure compliance with GMP and safety requirements.
• Prepare documents relating to manufacturing, plant turnaround, Local Work Instructions (WI), Local Standard Operating Procedures (SOP), Training Material (TRN) and Operations Logsheets to ensure that updated documents exist to support the activities of the Operations department. Documentation should comply to Data Integrity requirements and adherence to ALCOA principles.

We are looking for you with below attributes:

VS1 & Pilot Plant

• Degree in Chemical Engineering

What you will learn:

VS1 & Pilot Plant

• Foundational on-the-job training experience working in cGMP and key Global Supply API manufacturing site with state of art manufacturing facilities, including first in class Continuous Manufacturing facility
• To train to be an advocate for Continuous Improvement, with introductory basics on Lean Sigma concepts, learn to apply independently and lead others to do the same.
• Team leadership through influence and communication

Where will I be based?

You will be based at one of our manufacturing site in Singapore near Jurong.

How can I apply?

Applications are now open. Click on the button above to apply.

We recommend you apply as soon as possible, because we accept ongoing applications and offer positions on a first come, first served basis!

At GSK we value diversity and treat all candidates equally. We strive to make our recruitment process free of bias of any kind and aim to create an inclusive workplace at GSK. If you require any assistance, either to attend an interview or during the course of the recruitment process, please let us know.

This role is responsible for handling mainly DeltaV and BAS changes due to tech transfer, upgrades, and routine change, able to independently handle the validation of the mini projects so relevant experience is required.

Responsibilities:

• Manage Computer System Validation Lifecycle from design to execution phases, Including relevant CSV documentations such as Configuration specification, design review, commissioning documents, and protocols.
• Responsible for preparation of CSV documents and protocols, perform execution for automated equipment and/or control systems, and closure of executed protocols.
• Work largely requires use of valgenesis software to create validation documents and electronic test case execution
• Work with SME to generate test cases and CSV documents.
• Provide guidance on test case execution and exception handling.
• Support SME on documentation matters and ensure documents are completed in time.
• Any other task as assigned by Supervisor/Manager.

About You:

• Bachelor of Science/Engineering or higher in a scientific or engineering discipline
• Min 2 – 3 years of in validation (preferred equipment or CS validation)
• Understand validation principles and keen interest in CSV and
• Willing to learn and able to work with not much supervision
• Demonstrated proficiency of written and verbal communication skills with ability to communicate and collaborate effectively with cross-functional teams
• Must be team player, curious with strong analytical and organizational skills

Based in Tuas.

1 year contract. Option to extend/annual renewal depending on performance

• Performing construction site and safety inspections of all the operations and facilities.
• Providing communication and documentation of the inspections carried out including suggesting necessary corrective measures.
• Providing consultation and advice to the construction staff and assisting them to maintain a safe working environment to comply with safety regulations, practices and standards.
• Assisting the superiors to enforce the safety policy and environmental health guidelines.
• Training the construction staff on various health and safety topics.
• Providing direct technical surveillance and testing services as and when required.
• Knowledge of construction safety that includes inspection methods, procedures and practices, modern training and teaching methods and health and safety guidelines.
• Ability to develop and deliver safety and health training programs.
• Ability to communicate effectively in both oral and written.
• Establishing and maintaining an effective working relationship with representatives from regulatory organizations.
• Skill in operating technical testing equipment and instruments.
• Demonstrated good interpersonal skills.
• Good judgment, analytical and problem solving skills.
• Ability to take logical decisions.
• Detail oriented and accurate.
• Demonstrated ability for working independently under a minimal supervision.

Responsibilities:

• Software design, coding, testing, debugging and validating
• Software development and implementation for high-speed automated equipment
• Evaluating and establishing system performance and specifications
• Provide software technical support to a team of field service engineers
• Software maintenance of existing equipment

Requirements:

• Degree in any Engineering discipline with minimum 3 years of experience in software development in the automation / semiconductor industry
• Strong programming skills in C / C++
• Must have good hands-on experience in programming multi-threaded windows application using Visual C++
• Good knowledge of electronic components, motion control and interfacing with inspection systems
• Strong Mathematical and Algorithmic development skills
• Proficient in English (both written and spoken)

Additional info:

• Travel overseas for field support when required
• Supporting overtime when necessary

To apply, please visit www.gmprecruit.com and search for Job Reference: 24877

To learn more about this opportunity, please contact Yingying at [email protected]

We regret that only shortlisted candidates will be notified.

GMP Technologies (S) Pte Ltd | EA Licence: 11C3793 | EA Personnel: Lai Yingying | Registration No: R1110239

Scope

• In General, Plan, manage & control overall scope of Electrical works of

projects.

• Understand Project specifications, prepare specifications for electrical

equipment and systems

• Technically evaluate suppliers’ proposals.

• Guide Designers to prepare Sing[le Line Diagrams/Subcontractors in

producing Field Engineering Drawings and verify their accuracy based on

project specifications and applicable local and international codes.

• Manage Supervisors/Subcontractors for the execution of construction works

by regular visits and meetings.

• Interface with other disciplines proactively to ensure there are no

mismatches.

• Liaise with clients’ Engineers/ Supervisors and Professional Engineers for the

smooth execution of projects.

Requirements

• Recognized Degree in Electrical or Electronics or Instrumentation

Engineering with minimum 8 years relevant working experience, preferably in

the chemical engineering industry.

• Experience with 22KV & LV Electrical system is required preferably in

Singapore and understanding of Singapore codes.

• Matured, Proactive, leadership qualities, good communication and

interpersonal skills are essential and willing to work longer hours based on

project needs.

• Familiarity with relevant Local & International Engineering Codes and

Practices.

• Senior positions will be considered for candidates with more experience in

the relevant field

Duties:

· Plan, manage and co-ordinate all activities related to the work programmes;

· Prepare and submit all programmes, schedule, method statement, technical proposal, risk assessment plans prior to commencement of work to the SO;

· Co-ordinate and attend all meetings;

· Ensure that all Works carried out are in accordance to the Specifications;

· Work out estimates for the work;

· Put up traffic control/diversion plan for every stage of the work;

· Taking and scheming of road levels where required;

· Pick up manhole details and existing traffic lines or schemes on the road;

· Submit the detailed calculation and plans to the SO or his representatives;

· Ensure that all the plant and equipment are in good working condition and the temporary signing arrangement is in accordance with the traffic arrangement plan submitted by him or in accordance with the Code of Practice for Traffic Control at Work Zone before the commencement of work;

· Plan and ensure the smooth operation of the work;

· Ensure that the work carried out is according to the Specifications; and

· Other duties as instructed by the SO or his representatives.

Requirements:

· At least five (5) years relevant local experience in managing road structure construction or maintenance and a degree in civil engineering recognised by the professional engineers (PE) board or qualifications acceptable by the commissioner of building control for registration as resident engineer

Position Overview:

As design verification engineer, you would be part of a passionate verification team that is constantly pushing the limits – developing and deploying state-of-the-art verification methodologies in ever-increasing design complexities, from UVM, C/C++ co-simulation, system emulation to mixed-mode simulation & formal verification. The goal is simple – to achieve zero-defect with the best and smartest approach to the large verification space.

Requirements:

1. Experience in UVM verification methodology

2. Disciplined, quality-minded, and highly driven for excellence,

3. Excellent team player and good communication skills

4. MSEE/BSEE in Electrical Engineering or Computer Engineering, with 3 years of relevant experience, but are open to fresh graduates with outstanding results

5. Candidates with relevant experiences would be offered as Senior or Staff, taking on higher responsibilities

6. Experience in video processing and video analytics is a plus

7. Passionate and strong in general programming is a plus

The School of Chemistry, Chemical Engineering and Biotechnology (CCEB) invites applications for the position of Project Officer. The candidate will have the opportunity to explore his/her own interests across functions.

Key Responsibilities:

• Design and characterize novel biodegradable, biocompatible materials and tissue scaffolds with controlled drug/gene/cell delivery capabilities for soft tissue engineering & stem cell engineering.
• Design, optimize and fabricate tissue scaffolds (e.g. hydrogels, injectable scaffolds, electrospinning, 3D printing)
• Characterize scaffold properties: physical, chemical characteristics, drug/gene release kinetics, cell/tissue interactions, etc.
• Design and execute experiments independently.
• Expected to interpret experimental results, and author papers in high-quality journals in areas that are related to the research.
• Work closely with the Principal Investigator to help supervise and train junior lab members and to ensure smooth functioning of an active research program.

Job Requirements:

• Bachelor’s degree in Biomedical Engineering with relevant background and experience.
• Published experience in biomaterials scaffold design, fabrication and characterization, controlled drug/gene delivery design and characterization. Evaluation of cellular response/interactions/functionality with scaffolds using western blotting, immunostaining, qPCR, fluorescent microscopy (confocal) imaging, functional assays.
• Experience in 3D printing is a plus.
• Strong ability to communicate effectively orally and in written form.
• Strong ability to perform independent, self-directed work.
• Strong organizational skills and proactive personality with outstanding motivation, creativity, critical and analytical thinking skills, strong scientific commitment and ability to work as a team.
• Demonstrate excellent communication skills and have a strong passion and commitment to science.
• Expected to work in a collaborative inter-institute environment.

We regret that only shortlisted candidates will be notified.

Job Description

• Industry/ Organization Type: Building & Construction
• Position Title: Site Engineer
• Working Location: Pioneer
• Working Hours: 5.5 working days (Mon to Fri 8AM – 5PM, Sat half day)
• Salary Package: Basic Salary up to $6,800 + AWS + Variable Bonus + Transport Allowance
• Duration: Permanent

Key Responsibilities

• Working with professionals for the building and maintenance of Formula One Race Track
• Monitoring of road levels, work out estimates for proposed work and putting up traffic control plan
• Carry out site measurements and prepare job measurements for ordering of required premix
• Planning and supervising of assigned project which includes night work as scheduled by LTA
• Manage race track construction team and adhere to health and safety guidelines
• Undertake risk assessments, deal with client, transport specialists and members of public
• Submit weekly progress report and attend monthly progress meeting
• Ensure machineries and equipment are always kept in good working condition
• Any other ad-hoc duties as assigned

APPLY NOW!!!

• Minimum Diploma in Civil Engineering or related qualification
• Must have working experience with Formula One projects
• Has experience with Land Transport Authority (LTA), Strategic Planning Policy Group (SPPG) or Defence Science and Technology Agency (DSTA)
• Prior experience with road construction and resurfacing is required
• Proficient in MS Office
• Class 3 driving license is required

Kindly apply through ANY of the following methods:

• Submit your application by clicking the APPLY button;
• Email your resume to [email protected]. Please indicate #70470 on the email subject.

Anradus Application Policy: We value each application and ensure every resume is reviewed. Our process is efficient, typically concluding within 3 working days. If you do not receive communication from us within this timeframe, it's likely that your application has not been shortlisted by our client. In such cases, we recommend continuing your job search to maximize your opportunities.

Anradus Pte Ltd | EA License No. 20C0161 | Adelin Chong | EA Reg No.: R1875641

Job scope:

• Dealing with all related stakeholders for the M&E projects
• Understanding market price trends
• Capable of administrate on ACMV/Electrical tender and tendering procedures
• Controlling, planning for strategy of all tendering duties
• List the scope of work and commercial requirements in order to determine the risks of the projects
• Preparing and follow up on the Request For Quotations to suppliers/sub-cons in order to ensure tender costing and technical data to be submitted on time
• Taking off Bill of Quantities from the ACMV Drawings, Points of Schedules and
• Architectural drawings
• Collating price comparison, costing summary and technical proposal in order to prepare tender submission
• Studying the addendum and/or corrigendum documents and update costing summary with technical proposal accordingly
• Diploma/Degree in any engineering related field
• Quantity surveyor experience from M&E construction field
• Salary up to $4000

Interested candidates please apply online or send your latest CV to [email protected]

Kindly note that only shortlisted candidates will be notified.

AlwaysHired Pte Ltd

Reg No: R1441412

EA: 24C2293

Job duties:

• Conducting performance testing for electrical systems & marine engines
• Troubleshooting and overhaul marine engines and generators
• Making sure all repair procedures are done based on the service manual
• Conducting on site & in house calibration
• Marine mechanic working experience before
• Ensuring safety number one
• Willing to work in marine engine room and offshore environment
• Willing to travel overseas if required
• Basic Salary Up $2500 + Housing Allowance + Overtime Allowance + Overseas Allowance
• AWS + Variable bonus
• Good medical insurance and claim

Interested candidates please apply online or send your latest CV to [email protected]

Kindly note that only shortlisted candidates will be notified.

AlwaysHired Pte Ltd

Reg No: R1441412

EA: 24C2293

Experience: 1-5 Years

Role: System Engineer

Key Skills: Nice Engage Voice Recording systems admin

Key Responsibilities:

Support Unified Comms Systems

· Maintaining Unified Comms system through preventive maintenance and follow ups on problem resolutions.

· Attending to user requirements and work with vendor to provide solutions.

· Work with other departments for smooth flow of processes and procedures.

Projects rollout

· Plan technical deliverables including system enhancements and upgrades to meet project requirements within allocated budget and schedule.

· Plan resource allocation and utilisation across the various project and quarterly releases.

· Plan and collaborate across different application teams and overseas counterparts to manage technical dependencies of the solution in the project delivery cycle.

· Monitor and manage risks /issues related to technical delivery.

Key Requirements:

1. Skilled in NICE Engage Voice Recording systems administration.

2. Experienced in various roles in Service Delivery, Vendor Management and Incident / Change Management

Job Description

• Responsible for the installation and daily operations support for facility management of client platforms to meet agreed business needs & service levels.
• Perform troubleshooting for client platform related problems
• Respond promptly to incident, investigate & provide temporary &/or permanent resolution of incidents escalated.
• Provide timely status updates to relevant parties.
• Perform service request related to client platforms.
• Monitor the agreed service level, document & maintain the configuration of the systems; provide regular reporting to relevant parties.
• Involve in client platform implementation/upgrade project.

Skills Required

• Minimum 1 year relevant experience in providing desktop support
• Proficient in Microsoft Windows / Windows XP / Microsoft Office
• Experience in providing desktop support to senior management

To apply please click the Apply button or send us your updated profile to [email protected]

EA Licence No.:18S9405 / EA Reg. No.:R1330864

Percept Solutions is undergoing a growth phase and are on the lookout for talent. Applicants are encouraged to follow Percept Solutions on LinkedIn @ https://www.linkedin.com/company/percept-solutions/ to stay up to date on our upcoming roles and events.