Basic Qualification/ Skill required

Minimum - ITE (Electronic ) and skill is the most important qualification.

These are the scope of work if you have no experience and are willing to learn.

Will be performing initial testing, analysis and repair of PCB, and other electro-mechanical assembly.

Responsibility

1. Maintain documentation of parts condition upon arrival, during repair as well as final testing prior to shipping out repaired parts.

2. Repair populated PCB which include but not limited to digital board, analog board, RF,etc.

1. Familiar and proficient with different soldering and desoldering technique (Through hole component, smd, bga).

2. Must be familiar with at least one of the following and able to recognize main building block of : SMPS power supply, Servo amp, stepper motor driver, linear power supply.

3. Able to use oscilloscope to troubleshoot parts, power supply to provide power to board under repair, soldering, station, desoldering station, multimeter.

4. Advance skill that will be a plus point.

5.Knowledge of servo motor, encoder and servo amplifier (Sanyo)

6. Programming skill (C, python, basic , other language).

7. Arduino, Raspberry pi, or any other micro controller and sbc.

8. Understanding of reverse engineering technique as well as ability to reverse engineer a PCB, repairing without schematic availability.

Salary will commensurate with skill and experience

5 days work week

• Assess and negotiate incoming Maintenance & Repair estimates with the respective repair vendor/depot.
• Make sure the best possible Maintenance & Repair quality in a most cost effective manner.
• Verify incoming Equipment Check reports (ECR) for plausibility and correctness.

Requirements:

• Nitec in Industrial Engineering/Mechanical Engineering or equivalent.
• At least 2 years of relevant working experience
• Strong technical knowledge in tank containers industry.

If you are keen to apply for the position, kindly email your detailed resume in MS Word to [email protected]

Please note that only shortlisted candidates will be notified.

For more job opportunities, please visit our website at www.recruit-expert.com

EA Licence: 19C9701
Registration: R21100996

about the job

• Oversee all aspects of component repair operations for Commercial Engines business
• Product portfolio comprises of commercial and military aircraft engine parts repair
• Drive operational excellence and be accountable for engine on-time delivery and contractual TAT, cost
• control, productivity hit-ratio metrics as well as quality and safety compliance
• Plan and control repair production as well as allocate manpower and resources
• Manage component repair revenue hours
• Ensure compliance of quality standards and regulations
• Lead in customer focus teams to liaise with customers
• Provide leadership and guidance to production team
• Lead Continuous Improvement/ Kaizen /Digitalization /Automation initiatives

skills and experience required

• Bachelor's in Mechanical/Aeronautical Engineering Degree or equivalent
• Knowledge and experience in aircraft engine workshop practices and MRO of gas turbine engines
• Knowledge of aviation authority regulations (CAAS, FAA, EASA, CAAC)

If you are interested in the position, kindly send your CVs to sean.ho@randstad.com.sg

Please include your availability, expected salary and reason for leaving your current job.

We regret that only shortlisted candidates will be contacted.

Applicants must be fully vaccinated or have a valid exemption in accordance with MOM’s regulations to allow them to enter the workplace. Applicants may be required to share verifiable COVID-19 vaccination documents or proof of a valid exemption at the point of offer. Randstad Pte. Limited and/or the Client reserves the right to withdraw an offer if the applicant fails to provide verifiable COVID-19 vaccination and/or proof of exemption documents.

Chin Swee Rd (near Chinatown MRT)

6 days (8 hrs/day including 45 mins break)

Shift hours: 7am – 3pm; 3pm – 11pm; 11pm – 7am

$1900 - $2300

Responsibilities:

• Attend to guest room and public area maintenance as reported by Front Office and Housekeeping.
• Carrying out preventive maintenance of all electrical installations and equipment.
• Other tasks and responsibilities includes upkeeping and maintenance of fixtures & fittings, carpentry, painting and plumbing works.

Requirements:

• Possess minimum National Technical Certificate – 3 (NTC 3)
• Able to perform 3 rotating shifts, including weekends and public holidays.

Chin See Min Reg No. : R22107450

The Supreme HR Advisory Pte Ltd EA No. : 14C7279

Chin Swee Rd (near Chinatown MRT)

6 days (8 hrs/day including 45 mins break)

Shift hours: 7am – 3pm; 3pm – 11pm; 11pm – 7am

$1900 - $2300

Responsibilities:

• Attend to guest room and public area maintenance as reported by Front Office and Housekeeping.
• Carrying out preventive maintenance of all electrical installations and equipment.
• Other tasks and responsibilities includes upkeeping and maintenance of fixtures & fittings, carpentry, painting and plumbing works.

Requirements:

• Possess minimum National Technical Certificate – 3 (NTC 3)
• Able to perform 3 rotating shifts, including weekends and public holidays.

https://wa.me/6596420989

WhatsApp: +65 9642 0989 (Han)

Email: [email protected]

Chaw Chiaw Han, Reg No：R22106723

The Supreme HR Advisory Pte Ltd, EA No：14c7279

Responsibilities

• Responsible for performing preventive maintenance and calibration of the machines according to the checklist
• Responsible in analysing machine problems and repair
• Responsible for updating and maintaining maintenance records and forms regularly

Requirements

• Min Nitec in Electrical Engineering
• Min 2 years of working experience in maintenance and repair of CNC metal cutting machines
• Knowledge in PLC will be advantage

Please kindly email your resume in Ms Word to [email protected]

We regret to inform that only shortlisted candidates would be notified.

Jane Neo

Registration Number: R1328870

EA License No. 22C1026

The successful candidate will be responsible for the full spectrum of engineering operations.

Lead and manage the maintenance department to ensure high quality standards for building maintenance, M&E operations, managing projects and implementing preventive maintenance programs to ensure that the facilities are well-cared for and adequately support the business operations.

Requirements:

• Possess a Diploma in M&E or its equivalent with at least 6 years’ experience in serviced apartment/hotel Engineering functions;
• Knowledge of Building Automation System preferred;
• Good leadership and effective time management skills;
• A qualified Fire and Safety Manager will be a plus, am well-versed in all maintenance process and health and safety rules & regulations.