As the Research Engineer (Equipment/Operations), you are directly involved in tool installation activities for semiconductor process tools. You would need to work proactively to coordinate with the contractor on the ground for the execution and take corrective and preventive actions of lessons learned, due diligently to prevent reoccurrence. You are responsible for performing utilities turn-on after installation is completed. You must perform the activities per ASTAR site procedure and safety policies to ensure all tool-install-related activities are completed, meeting safety, quality, schedule and budget requirements. You will also be required to perform other activities such as operations for the different semiconductor modules (Diffusion, Litho, Dry/Wet Etch, Thin Film, Implant, etc).

Responsibilities:

• Coordinate with all tool-install base contractors to execute equipment hookup for new tools, to meet the high-quality standards, dynamic schedule, and forecasted budget.
• Coordinate with the Project owner (NGTC/APM) to facilitate utility release as per the planned schedule and update tool release status timely
• Follow all safety and environmental procedures to ensure compliance with EHS-related regulations, risk assessment, safe work procedures, and permit-to-work system.
• Play an active role in safety, actively participating in safety discussions and safe work practices.
• Establish regular area walks to identify opportunities for improved safety, cleanliness, housekeeping and , efficiency
• Establish regular, working interaction with peers as well as vendors in tool installation & facilitation, communicating clearly and respectfully all relevant information.
• Keep the reporting officer informed regarding the progress of assigned work and any abnormalities observed in your area.
• Demonstrate ability to understand drawing and highlighting discrepancies
• Follow area-specific procedures and documentation
• Prioritize work tasks to meet schedule and expectations, minimum guidance
• Perform tool tool-relativities and cleanroom systems troubleshooting during the hookup phase
• To perform equipment trouble-shooting of the equipments in NGTC when the need arises
• To perform utility-on after installation completion and to work closely with LCAM for complete closure
• To perform tests balancing of exhaust for new tools whenever necessary
• To perform measures for tool consumption during the hookup phase and to work closely with LCAM
• Use methods to organize, calculate, and display data accurately for utility and flowrate measurement
• Perform site activities in accordance to the Discipline

Requirements:

• Degree/Diploma in Mechanical/Electrical/Chemical engineering or equivalent
• Semiconductor experience (Equipment & Process)
• Facilities field or Wafer Fab Manufacturing equipment background will be an advantage.
• AutoCAD

Summary

This position is accountable for preparing the detailed Construction plans in accordance with the JGCAP’s company policies as the key person under the direction by JGCAP’s Site In-charge/ Project Manager and coordinating all construction activities on site among all JGCAP’s disciplines including subcontractors using his technical experiences and construction know-how and ensuring the completion of the work on schedule.

The detail plans as described above are as follows:

• Execution formation with the direction by JGCAP’s Site In-charge/ Project Manager.
• Outline of the Construction & sequence of work.
• Temporary facilities plan (If require) and subcontracting Plan.
• Manpower mobilization plan.
• Construction equipment mobilization plan.
• Work closely with the project scheduler on construction schedule and progress reporting.
• Constructability studies and plans, coordinate with Project Engineers and other related discipline as and when necessary.
• Scaffolding plan.
• Reflect the constructability plans in the inquiry for subcontracting.
• Preparation of documents such as specifications, procedures, manuals and etc.
• Erection plan of extra heavy equipment, inclusive of haulage plan.
• HSSE work control plan including rules and promotion plan together with JGCAP’s Site HSSE personnel.
• Coordinate with Project team of vendor specialists for work which need vendor specialist support.

Duties & Responsibilities:

• Initiate the subcontractors sourcing, inquiry package issuing, work scope clarification, sub-contractors evaluation & selection, cost negotiation and PO issuance.
• Work scope clarification & confirmation, BQ verification and construction direct & indirect cost estimation.
• Initiate Project’s Kick off meeting with the selected subcontractor and coordinating with selected subcontractors to ensure they are in line with company or project strategies and planning. Discussing and clarifying the detail of scope of work, execution plan, commercial issue and technical issue to minimize potential future conflict.
• Carry out constructability studies, construction activities planning and execution plan for the job.
• Coordinating with all engineering disciplines to ensure design, cost and client’s requirement can be achieved.
• Handling of issued drawings or field change sheet to ensure latest drawings to be applied.
• Work closely with the team member and subcontractor to prepare all the MSRA required for the project.
• Working closely with scheduler, subcontractors and clients to plan ahead and schedule critical work paths in order to avoid delays or obstructions on mechanical completion.
• Day to day management of the site, including supervising and monitoring the work progress, site labour force and any work of subcontractors.
• Overseeing quality control and health and safety matters on site.
• Maintain knowledge on all contract terms and legal requirements for project to avoid any delay in projects.
• Identify and resolve all technical issues in Construction process.
• Liaising with clients and company project team, including attending regular meeting and submitting reports to keep them informed of progress and construction issues.
• Liaising with any vendors, consultant, supervisors, subcontractors and the general workforce involved in the project.
• Assist the JGCAP’s Site In-charge/ Project Manager to monitor and manage the overall construction cost, including subcontractors’ progress billing, construction expenses and cost of variation order.
• Prepare and submit the weekly and monthly progress/construction reports to management.

Education Qualifications & Other Requirements:

• Degree in Mechanical engineering or equivalent.
• Over 3 years’ relevant experience in construction management field.
• Candidate with vast experience is also encouraged to apply.
• Experience in oil and gas or chemical projects.
• Knowledge in construction planning.
• Knowledge and experience in sub-contracting work.
• Proficient in MS Office, MS Powerpoint and schedule reporting.
• Clear awareness of construction management tools and method of execution.
• Familiar with Construction Practices.

Interested parties, please send in your detailed resume.

Interested applicants are invited to apply directly at the NUS Career Portal

Your application will be processed only if you apply via NUS Career Portal

We regret that only shortlisted candidates will be notified.

Job Description

AI Singapore (AISG) is a national AI programme launched by the National Research Foundation (NRF) to anchor deep national capabilities in Artificial Intelligence (AI).

The programme office is hosted by the National University of Singapore (NUS) and brings together all Singapore-based research institutions and the vibrant ecosystem of AI start-ups and companies developing AI products to perform use-inspired research, grow the knowledge, create the tools, and develop the talent to power Singapore's AI efforts.

We are looking for a Senior AI Engineer to join AI Singapore to lead the evaluation efforts in the Applied Research for Foundation Models team in AI Products.

Duties and Responsibilities

• Support the development of NLP products for Southeast Asian languages, with a focus on foundation models and linguistically-motivated approaches.
• Aid efforts on the fine-tuning, alignment and reasoning of large language models, including research, experimentation, implementation and data creation where applicable.
• Keep abreast of latest developments in NLP for low-resource languages, evaluation approaches etc.
• Collaborate with various parties both within and outside of Singapore on research and software development

Qualifications

• Masters or Ph.D. in Computer Science, Machine Learning, AI, Statistics, Mathematics, Engineering or Computational Linguistics
• Background in Linguistics is highly preferred
• Competency in a Southeast Asian language, or knowledge of multiple languages is strongly preferred
• Familiar with modern NLP models, including transformer architectures and large language models
• Familiar with fine-tuning and alignment techniques related to chain-of-thought generation and reasoning in LLMs
• Familiar with NLP evaluation methods and metrics
• Experienced in NLP model implementations based on PyTorch or Tensorflow/Keras, with some exposure to the setting up of end-to-end pipelines from data preparation to deployment
• Fluent in Python, but other languages such as Java, C++ or Javascript will be a bonus
• Have a good grasp of the fundamentals of Machine Learning
• Knowledge and experience in Software Engineering will be beneficial (e.g. Agile framework, Frontend/Backend development, Git)
• Some knowledge of DevOps (Docker, Kubernetes, CI/CD) will be a plus
• Team player with good communication skills and passion for technology

Job Title: Assistant Engineer (ID4633)
Location: : Woodlands
Working Hour： Mon - Fri 8.15am- 5.30pm
Salary: $2600-$3000

Job Description:
• Assist in the design, development, and testing of mechanical systems and equipment.
• Support senior engineers in planning and executing projects.
• Perform routine maintenance and troubleshooting of mechanical machinery.Conduct inspections and quality checks on mechanical components.
• Assist in preparing technical reports, documentation, and drawings.
• Collaborate with other departments to ensure project goals are met.
• Monitor and ensure compliance with safety and regulatory standards.
• Provide technical support during installation and commissioning of equipment.
• Assist in solving mechanical issues and suggesting improvements.

Requirement
• Candidate must possess Diploma in Mechanical or Engineering|
• No experience require

Job Responsibilities:

• Design and develop high-quality, scalable, and maintainable mobile applications.
• Collaborate with cross-functional teams to define, design, and ship new features.
• Ensure the performance, quality, and responsiveness of applications.
• Identify and correct bottlenecks and fix bugs.
• Help maintain code quality, organization, and automatization.
• Stay up-to-date with the latest trends and technologies in mobile development.

Requirements:

• At least a minimum of 5 years of relevant experience in IOS/Android App development.
• Bachelors degree in Computer Science, Information Technology, or a related field.
• Strong knowledge of Flutter, React, Dart and native programming language.
• Proven experience in building mobile applications for Android and iOS.
• Understanding of the full mobile development life cycle.
• Familiarity with RESTful APIs to connect mobile applications to back-end services.
• Strong understanding of design principles and user interface guidelines.
• Excellent problem-solving skills and ability to work in a team environment.
• Good communication and interpersonal skills.

The above eligibility criteria are not exhaustive. A*STAR may include additional selection criteria based on its prevailing recruitment policies. These policies may be amended from time to time without notice. We regret that only shortlisted candidates will be notified.

Job Title: KDB+ Engineer (ID1384)
Location: Customer Site
Working Hours: Mon to Fri 9am to 6pm
Salary: $7000 to $7500

Job Description
• Implementation of Engineering/Architecture standards and programs
• Project management of key components
• Follow SDLC and Engineering standards
• Utilize knowledge of applications development procedures and concepts, and basic knowledge of other technical areas to
• identify and define necessary system enhancements, including using script tools and analyzing/interpreting code
• Consult with users, clients, and other technology groups on issues, and recommend programming solutions, install, and support
• Analyze applications to identify vulnerabilities and security issues, as well as conduct testing and debugging

Requirements:
• Bachelor's degree in computer science, information systems, or similar
• At least 1.5-2 years’ experience on KDB+ including the delta control platform (Kdb+ is a high-performance column-oriented database from Kx Systems Inc. kdb+ is designed to capture, analyze, compare, and store data − all at high speeds and on high volumes of data)
• Know how to use q (q is the general purpose programming language integrated with kdb+).
• Experience within the technology or banking industry
• Experience of developing or supporting q/KDB+ solutions
• Experience of developing Java solutions is a plus.
• Scripting (Shell)
• Unix (preferably Linux)

Position Summary:

This is for the Central Patch Management Service under the Systems Technologies which focuses on using BigFix for patch deployment, compliance, and reporting.

Roles And Responsibilities:

• Oversees the entire operation and understands how to use the tools & reports.
• In charge of the BigFix infrastructure, including servers, relays, SQL and updating of the software infrastructure.
• Control access to BigFix components.
• Work with various process owners and teams to develop and implement proposed ideas and automate repeatable tasks related to patch management.
• Develops custom reports for stakeholders.
• Setting up content for distribution to endpoints.
• Creates baselines, writes custom fixlets and analysis.
• Develop and maintain groups inside of BigFix.

Requirements / Qualifications:

• Minimum Bachelor's Degree or Professional Degree in Computer Science / Information Technology or equivalent.
• Proficient in BigFix architecture or SCCM
• Minimum 5 years and above of relevant hands-on experience in system operation support and project management.
• Proven ability to work creatively and analytically in a problem-solving environment demonstrating teamwork, innovation and excellence.
• Experience in troubleshooting, resolving, and communicating complex incidents and deep underlying issues to identify root cause.
• Possesses strong analytical skills to diagnose and address application problems.
• Result and customer oriented with multi-tasking capabilities.

Job Title: Sales Engineer (ID5039)
Location: Tuas
Working Hours: Mon to Fri, 8.30am to 6pm
Salary: $3400 to $4800

Job Description:
• Generating new customers base & maintaining relationship with existing customers
• Proactively identifying new business opportunities, developing, negotiating and closing commercial deals with customers
• Perform costing and submit quotation to customers which may include negotiating on tender, contract terms and sourcing for raw materials
• Providing the technical solution required to address client requirements
• Prepare sales order and necessary manufacturing documents
• Work closely with project management team in managing the project progress
• Participate in marketing efforts by the sales team through coordinating or attending trade shows and conferences
• Liaising with other members of the sales team, engineers and other technical experts

Requirement:
• Interested in sales
• Prior experience in the welding / oil & gas industry preferred
• Good interpersonal, communication
• Ability to read technical drawings
• Good in mathematics
• Strong desire and ability to learn quickly and acquire new skills
• Comfortable working independently

Interested applicants are invited to apply directly at the NUS Career Portal

Your application will be processed only if you apply via NUS Career Portal

We regret that only shortlisted candidates will be notified.

Job Description

We are seeking a motivated and skilled Research Assistant to join our team, focusing on the development and characterization of advanced 2D materials. The successful candidate will play a key role in supporting projects related to the growth, optimization, and detailed analysis of thin films for next-generation electronic devices.

Key Responsibilities:

• Materials Growth and Synthesis: Conduct thin-film deposition using techniques like Chemical Vapor Deposition (CVD) to synthesize 2D materials like MoS2 and other materials. Optimize growth parameters to achieve desired thickness, crystallinity, and uniformity.
• Characterization and Analysis: Utilize Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM), and Raman spectroscopy for in-depth material characterization, focusing on morphology, surface roughness, grain size, and crystallinity.
• Data Collection and Analysis: Systematically document experimental procedures, collect data, and analyze results. Interpret findings to drive improvements in synthesis protocols and optimize film properties.
• Research Documentation: Prepare comprehensive reports, summarize research findings, and present data to support ongoing projects and publications.
• Collaboration and Lab Support: Work closely with team members, provide support for collaborative experiments, and maintain laboratory equipment.

Qualifications

• Master’s degree in Materials Science, Chemistry, Physics, or a related field.
• Demonstrated experience with CVD, AFM, SEM, and other characterization tools for thin films and nanomaterials.
• Proficiency in handling 2D materials with a strong focus on growth and sulfurization processes.
• Ability to work independently and collaboratively, with excellent attention to detail and problem-solving skills.

This position offers a unique opportunity to contribute to cutting-edge research in materials science, focusing on 2D materials for advanced electronics. If you have a strong foundation in materials synthesis and characterization and are eager to develop innovative solutions, we encourage you to apply.

Key Responsibilities:
Provide day-to-day technical support and maintenance services, including troubleshooting and problem resolution
Monitor and maintain IT infrastructure, including servers, networks, and software applications
Assist in the implementation and upgrade of new IT systems and solutions
Communicate with vendors and clients to ensure technical needs are met
Write and update technical documentation and operation manuals
Participate in project planning and execution to ensure project goals are met on time
Track and report IT support incidents and problem resolution progress
Continuously learn and update technical knowledge to stay industry-competitive

Basic Requirements:
1-2 years of relevant work experience
Diploma in Computer Science, Information Technology, Computer Engineering, or a related major

-------------

Send me your resume via WhatsApp ❤

WhatsApp: (https://api.whatsapp.com/send?phone=6592377799)

I regret to share that only shortlisted candidates will be notified. www.dadaconsultants.com

EA Registration Number: R22108564

Data provided is for recruitment purposes only

Business Registration Number: 201735941W.

Licence Number: 18S9037

Interested applicants are invited to apply directly at the NUS Career Portal

Your application will be processed only if you apply via NUS Career Portal

We regret that only shortlisted candidates will be notified.

Job Description

You will work as an integral part of the laboratory operations team, providing support to the laboratory manager in operations and related laboratory duties such as safety matters, procurement and core equipment training. If you thrive in a dynamic environment and have a passion for managing laboratory operations and contributing to scientific advancements, this role could be an exciting fit for you!

Key Responsibilities

• Oversee the daily operations of the laboratory, ensuring that all processes and procedures are followed accurately and efficiently
  Facilitate training and development of laboratory users
  Support the operations team on laboratory safety and documentation
  Ensure compliance with all relevant regulations and safety standards to maintain a safe working environment
  Manage the laboratory procurement of equipment and supplies, including negotiating contracts with vendors and suppliers
  Implement and oversee maintenance schedules for laboratory equipment to ensure optimal performance and longevity
  Maintain the microfabrication cleanroom in functional state
  Stay abreast of technological advancements to enhance operational effectiveness.
  Other ad-hoc duties

Qualifications

• Bachelor’s Degree in Engineering or related field from a reputable university
• At least one year of working experience in a research/laboratory environment and familiarity with research operations
• Working experience in rapid prototyping, CAD or cleanroom microfabrication is preferred, but not necessary
• Understanding of safety regulations and compliance
• Ability to work cooperatively and communicate effectively with team members and researchers
• Passionate in mastering research equipment and passing on knowledge to users

To apply, please send your cover letter, CV and three references (name, institution, email). Only shortlisted candidates will be contacted.

Job Description:

Be part of an exciting team working on cutting-edge advanced packaging process technologies. Participate in process development and integration solution to enable advanced packaging process technologies in the world of mobile, IoT, consumer and high-performance computing area. Partner and work with various teams from inside and outside of IME to help develop leading-edge packaging solutions for our customers, taking the solutions from concept to mass production. Responsibilities will include assisting in operations support in clean room to make sure projects are completed successfully and delivered on time.

This position is based in Singapore.

Responsibilities:

• Operate semiconductor equipment to perform processes, measurement, and inspection of wafers. (Include equipment setup, loading and unloading of wafers)
• Monitor basic equipment/process errors and perform recovery.
• Work with internal and external parties to align for tool time, execute process sequence and collect data to feedback to integration owner.
• Logistically transport wafer lots between equipment within cleanroom and between worksites.
• Identify and address potential areas for improvements such as cycle time, utilization, and cost.
• Perform chemical change/ top-up for equipment under supervision.
• Understand and follow all Environmental, Health and Safety (EHS) procedures and requirements.
• The candidate may be required to perform shift work (Mon-Fri).

Experience:

• NITEC/ Diploma in Electrical/Mechanical/Chemical Engineering
• Basic understanding on semiconductor process is preferred
• 1-3 years of experience in semiconductor processes (Litho, Etch, CVD, PVD, Plating, Metrology etc.) will be added advantages

Job Description:

Be part of an exciting team working on cutting-edge advanced packaging process technologies. Participate in process development and integration solution to enable advanced packaging process technologies in the world of mobile, IoT, consumer and high-performance computing area. Partner and work with various teams from inside and outside of IME to help develop leading-edge packaging solutions for our customers, taking the solutions from concept to mass production. Responsibilities will include assisting in operations support in clean room to make sure projects are completed successfully and delivered on time.

This position is based in Singapore.

Responsibilities:

• Operate semiconductor equipment to perform processes, measurement, and inspection of wafers. (Include equipment setup, loading and unloading of wafers)
• Monitor basic equipment/process errors and perform recovery.
• Work with internal and external parties to align for tool time, execute process sequence and collect data to feedback to integration owner.
• Logistically transport wafer lots between equipment within cleanroom and between worksites.
• Identify and address potential areas for improvements such as cycle time, utilization, and cost.
• Perform chemical change/ top-up for equipment under supervision.
• Understand and follow all Environmental, Health and Safety (EHS) procedures and requirements.
• The candidate may be required to perform shift work (Mon-Fri).

Experience:

• NITEC/ Diploma in Electrical/Mechanical/Chemical Engineering
• Basic understanding on semiconductor process is preferred
• 1-3 years of experience in semiconductor processes (Litho, Etch, CVD, PVD, Plating, Metrology etc.) will be added advantages

Job Description:

Be part of an exciting team working on cutting-edge advanced packaging process technologies. Participate in process development and integration solution to enable advanced packaging process technologies in the world of mobile, IoT, consumer and high-performance computing area. Partner and work with various teams from inside and outside of IME to help develop leading-edge packaging solutions for our customers, taking the solutions from concept to mass production. Responsibilities will include assisting in operations support in clean room to make sure projects are completed successfully and delivered on time.

This position is based in Singapore.

Responsibilities:

• Operate semiconductor equipment to perform processes, measurement, and inspection of wafers. (Include equipment setup, loading and unloading of wafers)
• Monitor basic equipment/process errors and perform recovery.
• Work with internal and external parties to align for tool time, execute process sequence and collect data to feedback to integration owner.
• Logistically transport wafer lots between equipment within cleanroom and between worksites.
• Identify and address potential areas for improvements such as cycle time, utilization, and cost.
• Perform chemical change/ top-up for equipment under supervision.
• Understand and follow all Environmental, Health and Safety (EHS) procedures and requirements.
• The candidate may be required to perform shift work (Mon-Fri).

Experience:

• NITEC/ Diploma in Electrical/Mechanical/Chemical Engineering
• Basic understanding on semiconductor process is preferred
• 1-3 years of experience in semiconductor processes (Litho, Etch, CVD, PVD, Plating, Metrology etc.) will be added advantages

Responsibilities:

• Develop software in embedded Android/Linux devices including software design as well as implementation and customization of solutions using Android/Linux operating systems.
• Perform system tunning/optimization and improve system stability using a strong background in embedded system,operating system, and multi-thread programming.
• Involved in system architecture and design and system requirements definition.
• Participate in requirements gathering, drive solutions, test, deploy, maintain and enhance embedded implementations.
• Ability to interpret and evaluate designs and assist in resolving firmware issues.
• Ability to conduct design reviews and incorporate knowledge of real-time embedded Android/Linux firmware.

Requirements:

• Degree in Electronic/Electrical/Computer Engineering/Computer Science, Software Engineering or related field.
• Good understanding of embedded Linux architecture.
• Minimum 8 years of hands-on experience with embedded Linux operating system, frameworks development, and C/C++.
• Minimum 5 years of hands-on experience with Linux bootloader and kernel.
• Must be able to develop solutions at the Linux device driver and HAL layers.
• Able to develop in Android Framework layers is an advantage.
• Experience working in a collaborative and distributed team environment.
• Proficiency in the use of debugging tools (ADB, JTAG, Kernel debug) applied to areas such as power management, task control, and memory management, as well as other complex debugging situations.
• Excellent teamwork skills, flexibility, and ability to multi-task.
• Able to manage one's time efficiently.

A world empowered by autonomy. We build robotic vehicles to improve logistics safety, forge a greener Earth, and enhance human lives.

We are a closely-knit team aspiring to change the world through disruptive technology. We are innovators. We are tinkerers. We are problem-solvers. And we have a fair amount of magic dust up our sleeves. We have a plan for fleet-level deployment of autonomous vehicles, and we are looking for the best-of-the-best to join us in making this a reality.

About Venti Technologies

Based in the U.S. and Asia, Venti Technologies is the leader in safe-speed autonomous logistics systems, developing the future of goods transportation. Using rigorous mathematics, deep learning, and theoretically-grounded algorithms, Venti has a proprietary collection of autonomy technologies including a suite of powerful logistics algorithms. Venti’s proven value proposition of saving costs, increasing vehicle utilization, and improving safety is recognized by customers and driving growth. Launched in 2018, Venti brings together an unsurpassed team internationally. The company has autonomous systems deployed in Asia for industrial and logistics sites and a growing pipeline. Venti has offices in Cambridge (Massachusetts, USA), Suzhou (China), and Singapore – our Asian headquarters.

Role responsibilities

• Be part of the team to architect and bring up the new data platform and service infrastructure for autonomous prime mover (APM) business.
• Architect proper data models to meet all business needs in APM R&D and production operation scenarios.
• Design and develop scalable and robust backend services to serve data to developers, operators, and customers for creating dashboards, reports, supporting machine learning needs and triage and troubleshooting.
• Design and develop large scale IoT system to track live operation data for fleet management.
• Bring up universal auth integration and best security practice.
• Provide common client SDK for all data platform backend services.

Required experience

• Bachelor’s or master's degree in computer science or related relevant field.
• 1+ years' experience in backend implementation and RESTful API implementation.
• Experience with RESTful API framework in Python, Java, or Golang.
• Experience with high performance backend implementation, profiling, and monitoring.
• Experience with data modeling with relational database and NoSQL database.
• Experience with docker, K8s or other containerization techniques.
• Experience with proper CI/CD setup.
• Excellent communication skills.

Salary is commensurate with experience. We also offer world-class benefits, fantastic culture, flexible working arrangements, and a great international working environment. Come and join us!

Job Description

The Engineer will be responsible for driving electro-mechanical product development in compliance with ISO 13485 standards across multiple levels, from component to product. The role includes planning and monitoring New Product Introduction (NPI) programs, managing engineering changes, and maintaining documentation, including Design History Files. The position requires close coordination with both internal and external suppliers, adhering to Quality Management System and regulatory standards.

Key Skills and Experience:

• Bachelor degree in Mechanical Engineering with 3+ years in electro-mechanical systems.
• Technical proficiency in optimizing designs for mechanical and electro-mechanical systems.
• Solid understanding of metal and plastic manufacturing processes for product design.
• Proficiency in 3D CAD software (e.g., SolidWorks), including GD&T and kinematic calculations.

Attributes:

• Analytical and detail-oriented, with a collaborative and hands-on approach.

The above eligibility criteria are not exhaustive. A*STAR may include additional selection criteria based on its prevailing recruitment policies. These policies may be amended from time to time without notice. We regret that only shortlisted candidates will be notified.

What you will do:
As Digital Solution Engineer/ Architect, you will be taking lead on application of digital software to our customer requirements and supporting digital sales specialists to sell the deals with include:

Client Engagement:

• Engage with prospective and existing clients to understand their business objectives, challenges, and technical requirements.
• Conduct discovery sessions to gather detailed information on customer needs, pain points, and success criteria.
• Develop and manage customer technical relationships, identify and expand digital opportunities.

Solution Design & Architecture:

• Develop customized digital solutions that align with client requirements, leveraging Johnson Controls’ digital OpenBlue portfolio, including IoT, AI, and data analytics platforms.
• Create and present high-level architectural solutions that address client needs, ensuring scalability, flexibility, and efficiency.

Technical Support to Sales:

o Qualify opportunities in terms of customer technical requirements and contribute to the Go/No-Go recommendations.

• Collaborate closely with the sales team to provide technical expertise throughout the sales cycle.
• Assist in the preparation of proposals, RFP responses, and presentations, ensuring they are technically accurate and compelling.
• Act as a technical advisor and thought leader to clients during meetings, workshops, and demonstrations.

Internal & External Digital Advocate:

o Enable the branch eco-system on technical aspect of the OpenBlue Solutions.

o Identify & train external partners to expand JCI digital solution business market reach

Product Demonstrations

• Deliver compelling product demonstrations that highlight the value and capabilities of Johnson Controls’ digital solutions.
• Tailor demonstrations to specific client needs, showcasing how our solutions can address their unique challenges

Solution Validation & Product Roadmap:

• Work with internal product teams to validate and optimize solutions for client-specific implementations.
• Provide feedback to product development teams on client requirements and market trends to inform future product enhancements.

Post Sales Activities:

• Support delivery readiness and gathering required documents including Scoping documents, IT approval, technical support during implementation
• Support Customer Kick-off meetings.

Documentation & Training:

• Develop and maintain technical documentation, including solution architectures, integration plans, and client-specific configurations.
• Provide training to sales teams and partners on new digital solutions and architectural best practices.

Industry Knowledge & Trends:

• Stay informed about the latest trends in digital solutions, smart building technologies, and industry-specific regulations.
• Share insights and best practices with clients and internal teams to drive innovation and competitive advantage.

How you will do it:

Technical Skills:

• Strong understanding of digital solutions, including IoT platforms, AI, data analytics, cloud computing, OT Cyber security and smart building technologies.
• Good understanding of building protocols like BACnet, Modbus, OPC, MQTT and other BAS protocols
• Proficiency in architectural frameworks, integration methodologies, and solution design best practices.
• Experience with relevant software and SaaS application in built or industrial environment.

Soft Skills:

• Commercial acumen
• Excellent communication and presentation skills, with the ability to convey complex technical concepts to non-technical audiences.
• Strong problem-solving abilities and a customer-centric mindset.
• Ability to work collaboratively in a cross-functional team environment

What we look for:

• Bachelor’s degree in computer science, Engineering, Information Technology, electronics, instrumentation, communication or a related field. A master’s degree is a plus
• Relevant certifications in cloud architecture, IoT, networking, cyber security or other digital technologies are a plus
• At least 6-7 years of experience in built or industrial environment.
• Minimum of 5 years of experience in a solution architect or presales role, preferably within the digital solutions, IoT, or smart building technology sectors.
• Minimum 3 years of experience in designing or delivering energy efficiency, workplace optimization, Asset Management, Facility management, HVAC optimization or digitization SaaS application in built or industrial environment.
• Proven track record of successfully designing and presenting technical solutions that meet client needs and drive business outcomes.
• Proficiency in APAC local language, Chinese is a plus as this position will require to liase with Chinese speaking customers.

What we offer:

• Competitive salary in a MNC environment
• Comprehensive benefits package
• On the job/cross training opportunities
• Encouraging and collaborative team environment
• Dedication to safety through our Zero Harm policy

Job Summary :

• Experience in Agile Delivery, Sprint Planning, Scrum Ceremonies, Retrospective and Release Planning, UAT testing & support
• Understand Requirements, User Stories and analyze it and capable of generating all types of positive, negative & failover scenarios, also the cross platform, cross browser etc.
• Good in test automation, UI test automation and API test automation.
• Expert in Cyrpess test automation
• Needs to be expert in test estimation and Test planning. Should know how to create useful, reliable and practical plans for software development projects.
• Excellent hands on experience in performing the Functional Testing and Regression Testing
• Should be good in test scenarios & test cases preparation and test execution, defect logging and reporting.
• Good experience in Wealth Management, Client Onboarding, Due Diligence Client Review Workflows and WM Regulatory.
• Experience working with Tools like Swagger, JIRA , Confluence, Gitlab, Soap UI and Postman
• Willingness to learn alternate technologies and tools, should be quick learner.
• Willingness to spend extra time to pick up client-specific Domain knowhow during KT sessions from SME
• Superior communication and stakeholder management skills. Independent, pro-active and self-motivated.
• Coordinate with Product Owners & Users for User Acceptance Testing (UAT) for release and Test Data Preparation.
• Prepare Testing Metrics & Reporting
• Managing and maintain Jira Board / Git issues and product backlogs in consultation with product owner
• Should be good individual contributor and good team player

Interested applicants are invited to apply directly at the NUS Career Portal

Your application will be processed only if you apply via NUS Career Portal

We regret that only shortlisted candidates will be notified.

Job Description

The Research Engineer will be involved in developing computer models for assessing climate change impacts on marine ecosystems. He/she will also be involved in collecting field data for calibrating and validating model systems. In addition to the above, the Research Engineer is expected to also participate actively in research meetings, present research findings, write reports and research papers.

Job Requirements

• Possess at least a good Bachelor’s degree in Civil and/or Environmental Engineering or equivalent.
• Experience in computational modelling in environmental engineering or climate change is preferred.
• Open to fixed term contract

Duties and responsibilities:

Planning and organizing construction projects, including developing project timelines, budgets, and resource plans.

Ensuring that all construction work is carried out in compliance with building codes, safety regulations, and other legal requirements.

Managing project teams, including architects, contractors, and other stakeholders, to ensure that projects are completed on time and within budget.

Monitoring project progress and making adjustments as necessary to ensure that projects are completed on time and within budget.

Collaborating with architects and other stakeholders to develop project plans and specifications.

Developing and implementing quality control procedures to ensure that construction work meets the required quality standards.

Providing technical guidance and support to project teams, including architects, contractors, and other stakeholders.

Maintaining accurate project records and documentation.

Develop and manage project schedules, budgets, and resources

Coordinate with architects, engineers, and contractors to ensure project success

Review and approve project plans, specifications, and contracts

Ensure compliance with building codes, safety regulations, and environmental requirements

Monitor project progress and make adjustments as necessary

Communicate project status to stakeholders and senior management

Manage project risks and identify opportunities for improvement

Provide technical support to project team members

Ensure quality control and quality assurance for all project deliverables

Lead project meetings and facilitate communication among team members

Assist in the development of cost estimates

Assist the project team with site safety documentation and coordination

Assist the project team with closeout of the project

Assist project accountant with monthly subcontractor billings and pay applications

Assist project manager with assigned tasks

Requirement:

Bachelor's degree in Civil Engineering or related field

Minimum of 5 years of experience in construction project management

Strong knowledge of construction materials, methods, and regulations

Excellent communication and leadership skills

Ability to manage multiple projects simultaneously

Proficiency in project management software and tools

Experience in managing large-scale construction projects

Ability to read and interpret blueprints and construction plans

Knowledge of budgeting and financial management

Experience in managing and supervising construction teams

Strong problem-solving and decision-making skills

Job Description:

Be part of an exciting Team working on cutting-edge advanced packaging process technologies. Partner and work with various FAB users, to always enable smooth operations and develop packaging solutions and taking the solutions from concept to production. Responsibilities will also include assisting in operations support in FAB clean rooms to make sure all rounded supports are provided.

This position is based in Singapore.

Responsibilities:

• Looking for a reliable, agile, and professional individual.
• Oversee the Team spare/ chemicals / inventories stores – upkeep with good house-keepings, periodic cycle counts. Maintain the inventory database, ensuring timely and accurate recordings, raise purchase requests accordingly.
• Take charge and provide day to day supports in all logistics needs and initiate material/spare parts procurement when required to ensure smooth Fab operations.
• Accountable for the inventory movements required to enable smooth lot operations across IME Premises.
• Follow through the orders from the start of purchase till delivery and to ensure that goods are delivered are on time.
• Work seamlessly with various stakeholders to provide logistics support and deliver inventory on time.
• Work towards and employ critical thinking, put-up good initiatives to move forward to digitalization.
• Ability to work in a multi-task environment.

Experience:

• Education: Diploma in engineering discipline. Preferably in supply chain logistic/ warehouse operations.
• At least 2 years of warehouse operations.
• Preferably some experience in semiconductor / manufacturing environment, with good wide contacts with semiconductor material suppliers, equipment vendors.
• Strong knowledge-based on excel skills and some knowledge of supply chain analytics.

IT Support Engineer

Responsibilities:

- Installing and configuring computer hardware, software, systems, networks, printers etc

- Responding in a timely manner to service issues and requests

- Providing technical support across customers

- On-site support for IT related issues at customer office

- Performing & maintaining customers’ IT inventory list

- Handling server related issues through the ticket system, escalate to server supplier TAC and follow up accordingly.

- Replace parts for servers like mainboards, CPU, RAM, HDD/SSDs, network linecards / modules, transceivers and cables

Requirements:

- Diploma in Computer Science, Information Technology or related disciplines

- Strong interpersonal and communication skills and the ability to work effectively with a wide range of constituencies in a diverse community.

- Troubleshooting & Problem-solving skills

- Ability to determine computer problems and to coordinate hardware, software, and/or network solutions.

- Ability to communicate technical guidance and instruction to users on the use of PC and/or mainframe applications and systems.

Capable of working in a fast paced environment

- Knowledge of a wide range of computer systems software, applications, hardware, networking, servers and communications.

- Familiar with data center environment is a PLUS

------------- Send me your resume via WhatsApp ❤

WhatsApp: (https://api.whatsapp.com/send?phone=6592377799)

I regret to share that only shortlisted candidates will be notified. www.dadaconsultants.com EA Registration Number: R22108564

Data provided is for recruitment purposes only Business Registration Number: 201735941W. Licence Number: 18S9037

You will work in the Environmental Health Institute, and be a key member of the Facility & Safety Management Section, overseeing facility support and safety management across multiple locations (Biopolis,Techplace II and Van Kleef Centre). This role encompasses a wide range of infrastructure and built environment responsibilities, making it ideal for engineers looking to apply their expertise in a dynamic research setting.

This job might be for you if you possess the following qualities:

• Lead strategic planning and coordination for establishing and maintaining specialised laboratories, ensuring alignment with organisational objectives and timelines.
• Develop and manage comprehensive project budgets, oversee financial planning, cost control, and resource allocation for laboratory establishment and maintenance projects.
• Create detailed project plans for laboratory establishment and maintenance, including scope definition, objectives, timelines, and resource requirements.
• Conduct cost-benefit analyses for proposed projects and initiatives, ensuring efficient use of resources and alignment with budgetary constraints.
• Oversee the design, installation, and maintenance of critical infrastructure systems, with a focus on Air Conditioning and Mechanical Ventilation (ACMV), and specialised laboratory equipment.
• Manage building automation systems to enhance facility performance and user comfort.
• Implement and oversee quality assurance processes to ensure specialised laboratories meet stringent quality standards and regulatory requirements.
• Identify potential risks associated with laboratory operations and develop robust mitigation strategies for safe handling of hazardous materials.
• Develop and implement sustainability initiatives across facilities, integrating innovative engineering solutions to optimise building performance and energy efficiency.
• Monitor and report on environmental performance metrics, including energy consumption and waste generation.
• Facilitate effective communication with stakeholders, including researchers, consultants, contractors, equipment suppliers, and regulatory authorities.
• Participate in corporate projects and perform administrative tasks as assigned.

Job Requirements:

• Degree in Mechanical Engineering. Candidates with degrees in other engineering disciplines (e.g., Electrical, Civil, or Environmental Engineering) with relevant experience will also be considered.
• Experience in facility infrastructure management, particularly in specialised laboratory or research environments.
• Expertise in designing and managing ACMV systems, and other critical building systems.
• Strong background in project management, particularly in complex built environments.
• Thorough understanding of regulatory requirements for specialised laboratories, including safety protocols for handling hazardous biological and chemical materials.
• Experience with Government Procurement practices, including green procurement initiatives.
• Proficiency in building management systems and CAD software.
• Strong analytical and problem-solving skills to address complex infrastructure challenges.
• Passion for driving sustainability in scientific research environments.
• Knowledge of green building standards (e.g., Green Mark) and experience implementing energy-efficient solutions.
• Excellent interpersonal and communication skills.

Applicants will be updated on the status of their applications within 4 weeks of the closing date of this job posting.

To apply, please proceed to Careers@Gov at https://sggovterp.wd102.myworkdayjobs.com/PublicServiceCareers/job/NEA-BIOPOLIS-HELIOS/Senior-Engineer-Executive-Engineer--Facility---Safety-Management-Section-_JR-10000034932

NEU Battery Materials is a lithium-ion battery recycling startup. We are building the world's first electrochemical process for battery recycling and we target batteries such as those in our electric cars. We hope that we can create a sustainable future for everyone, by providing an end of life solution to these batteries. We are currently building and operating our plant in Singapore and we look forward to welcoming additional team members to join us in our fight against climate change.

Job scope:

1. Design, plan, and implement our layout for our recycling equipment to optimize production and decrease costs
2. Assemble, operate, and maintain pilot scale recycling system
3. Develop and implement safety procedures for our team
4. Facilitate trial production to support product improvement and development
5. Identify areas of opportunities for process improvement, modification, and optimization ideas

Requirements:

1. Qualifications: Degree in Chemical Engineering or a related discipline with at least 2-3 years of relevant experience
2. Self-driven, independent and resourceful
3. Effective team player with good communication and presentation skills
4. Possess good analytical thinking and problem solving skills
5. Excellent communication in English
6. Good to have knowledge in any of these areas; flow battery, redox flow processes, electrochemical processes, fuel cell