. QAQC Inspector (Fabrication /Welding)

Responsibilities:

• Preparing or establishing that a welding procedure is available, has been approved as

required by the appropriate authority and is being employed in production.

• Witnessing of welder and procedure approval tests that including of the preparation of test

pieces and destructive tests and verifying compliance with appropriate standards and

specifications.

• Verification that adequate and valid welder approvals are available, and that only approved

welders as required are used in production.

• Interpretation of weld drawings and weld symbols.

• Performing of visual inspection and ensure that all finished goods are checked and approved

prior to any delivery of handover.

• Verification that post weld heat treatment has been conducted in accordance with

specification requirements.

• Appreciation of the factors influencing the formation of weld defects and their acceptability

in relation to the written specification.

• Coordination with QC Inspector (Hull/Structure and Piping) and NDT Coordinator, to verify

and ensure that all finished welds are checked and approved prior to any delivery of

handover.

• Ensure that quality assurance standards and procedures are maintained.

• Ensure that reports that are required are completed accordingly to the project

specifications.

• Liaise with Contractor, Production and Client’s representative to ensure the product is

checked and complied with the project quality plan and specifications.

• Perform any other tasks as may be assigned by the supervisor.

• Ensure compliance to relevant government regulations and company’s quality, safety, health

and environmental (QSHE) policies, practices and procedures at all times.

Requirements:

• Minimum Diploma in Engineering or relevant field of International certification (e.g. AWSCWI or CSWIP 3.1 WI).

• Physically fit since some of tasks require lifting of some equipment.

• A team player with the ability to work independently as well as in a team

• Good communication skills, meticulous, resourceful, able to multi-task

• Computer literary (MS. Office).

Job Description..

• Ensure all packing workers are performed their jobs according to the written work instructions.
• To place packaging materials from the store by based on the packing plan.
• Verify and monitor the work done by Group Leaders and Inspectors.
• To handle and follow up on the problems forwarded by Group Leaders.
• Checked and reviewed all checklist and reports by Group Leader and below by timely basis.
• Assist final packing area.
• To provide on the job training to the Packers, Inspectors, Group Leaders other support operators.
• To ensure packing procedure and packing method are implemented and practiced.
• Ensure storage, packaging, online and final packing area are clean and tidy at all times.
• Ensure the product is stored, labeled and segregated at designated area.
• Ensure worker is handle products in correct manner and not causing any damage or contamination onto the products.
• Inform to Executive/Engineer or Manager for any equipment need to be repair, service or calibrate.
• To conduct appraisal for the worker during probationer period.
• Any other task that may be assigned.
• Help packing at warehouse.
• Performance the QAQC task in the warehouse.
• Paying attention to detail, especially when it come to quality control.

Job Descriptions :

• Leadership and Coordination: Spearhead the delivery of Quality work scopes ensuring seamless coordination among stakeholders and compliance with applicable requirements. You’ll work alongside functions such as Package Mgmt, H&S, Engineering, Construction, Supply & Expediting, Commissioning, Project Controls, Contract Management, Legal, and Procurement.
• Quality Management: Drive project to completion on time, within budget, and to the highest quality and HSE standards. Develop and maintain project Quality schedules, budgets, and forecasts, contributing directly to Company’s Renewable strategy. Ensure compliance to Project Quality requirements are met.
• Design and execute a comprehensive strategy that integrates quality management with sustainability goals to support growth objectives
• Supervise, coach and engage the Quality team to strive for excellence, to deliver solutions that meet high-level quality standards
• Continuously improve customer satisfaction by handling customer complaints promptly and professionally
• Ensure products meet quality standards before reaching customers.
• Oversee all new product development procedures, ensuring that sustainability considerations and internal controls are integrated from the beginning.
• Risk Management: Effectively manage project risks, specifically those intrinsic to the offshore wind industry, manufacturing, Quality Assurance/Quality Control, and supply chain challenges.
• Ensure that the lessons learned are effectively captured and communicated during the project
• Expected to travel to Batam to monitor and control the construction progress and customer meetings.

Job Requirements :

• Bachelor’s degree or higher in Engineering, Mechanical Engineering, or a related field.
• 5-8 years of experience managing quality of Shipyard and installation. Experience in Quality Assurance and Quality Control for onshore / offshore wind projects, preferably specific to Offshore substation construction
• Proven success in quality and process management, with a track record in quality control and continuous improvement.
• In-depth knowledge of Quality Management Practices and standards such as ISO, APQP, PPAP, FMEA, MSA, REACH, ROHS.

The Production Control Analyst monitors inventory status and stock availability, and prepares orders for parts and material procurement. He/she also checks the accuracy of invoices received for spares and consumables, and maintains records in the enterprise resource planning (ERP) system. He/she plans production schedules and resources to meet production requirements and assist team members in ensuring adherence to the planned production schedules.

Purpose: To create, control and manage changes to customer's Technical Product Data (TPD) packages (Items, Bill of Materials, Product specification documents) in the Product Lifecycle Management (PLM) and Enterprise Resource Planning (ERP) systems. To deploy TPD changes to the relevant Persons-in-Charge (PICs) for execution.

Key Area of Responsibilities:

• Check the correctness and completeness of product packages, such as Technical Product Data (TPD) and Bill of Materials (BOM) received from customers.
• Work with the user of TPDs to define the new TPD requirement and update the ISO document (for new customers or any change in TPD requirement).
• Maintain required customer items, BOM, and TPDs in PLM and ERP systems.
• Create and control the item part number, BOM and TPD in the PLM and ERP systems.
• Create projects in the ERP system for the fulfillment of customer Sales orders.
• Implement Engineering Change Order (ECOs) and deploy the changes to the next inline PIC (such as planner, purchaser, process engineer and Sales & Program dept.)
• Check and ensure all required information for the TPD (items, BOMs, documents) and/or configuration change are provided, and approved by the customer.
• Support and participate in company continuous improvement program.

Qualification & Experiences:

• Diploma/Degree in Mechanical Engineering/Science or relevant field.
• Minimum 2 years of working as a product data engineer in the semiconductor industry or similar position.
• Proficient in Microsoft Excel functions
• Good communication skills

Purpose: The role is responsible for handling customer quality issues and continuous improvement activities of the Company products and processes. You are required to drive internal departments on quality-related issues to follow up on effective corrective/preventive actions. You will be liaising with the internal team to support QBR, RMA, IFR, MRB, FAI Review and approval with Supplier and customer, In-Process Audit, FA Launch, 8D, SDR, FPY, tracker processes, and communicate between customer and internal team on Quality related matters.

Key areas of responsibilities:

• Lead and drive customer quality CAB meetings to derive root causes and corrective and preventive actions based on 8D methodology
• Perform ad-hoc visits to customer sites to facilitate investigation and improvement proposal
• Develop, drive, and lead the improvement of manufacturing systems and processes to meet and exceed customer expectations
• Lead and drive company-wide continuous improvement projects with relevant Organizations
• Build and drive customer relationships to improve customer satisfaction
• Perform customer quality performance monitoring and reporting to internal management and customer
• Manage the first article process and submit the report to the customer for approval
• Lead cross-functional team to establish the outgoing inspection checklist for NPI to ensure that the product meets customer requirement
• Analyze customer quality performance to identify trends and improvement opportunities
• Perform manufacturing audit

Qualification & Experiences:

• Degree in Mechanical/Mechatronics/Electrical/Manufacturing Engineering discipline
• At least 5 years of working experience, 3 years in dealing with customer quality managers or direct customer facing, related to the manufacturing environment, preferably from the semiconductor, semiconductor equipment industry, electronics, or high-tech instrument industry
• Strong knowledge and practices in 8D, SPC, FMEA, 6-sigma methodology (Certified Black/Green Belt), and change management
• Good understanding of first-article inspection requirements and expectations
• Excellent leadership and effective communicator with all levels of associates and management
• Experienced in Minitab is an advantage
• Experienced QMS auditor

Job description / responsibilities / activities/ tasks:

Interpret project specifications and develop project quality plan in consultation with project manager and Shell Quality Lead,

Implementation of quality assurance and control activities in accordance with the project quality plan including but not limited to:

· Establish Field QC Organization, to manage field QC group and members including assignment of EPCm and/or contractor QC Inspectors. To interview all EPCm and/or contractor QC before assignment to Project

· Coordination with EPCm (optional), other disciplines and contractor’s approval of the Field QC related documents prepared by each Contractor,

· Attend KOM & Pre-Inspection Meeting with EPCm and Contractors depending on criticality of works,

· Review Contractor documents related to quality control (E.g. ITP, WPS, PQR, test packs, NDE procedures) and ensure compliance to the Project Spec’s & applicable Code Standard,

· Organize and lead on-Site quality patrols and audits to ascertain health of Project quality systems, Control of NCR’s & Quality observation Records,

· Verify that all the required inspection and documentation are completed by the contractor / Vendor and issuance of the Inspection Release Notice (IRN) to the contractor / Vendor prior to any Site delivery,

· Perform line checking, punch-listing & killing, witnessing various types of tests such as hydrostatic & pneumatic testing and monitor coordination of Pre-commissioning, flushing activities,

· Final acceptance sign off on quality test packages

Trouble shooting of major QC related issues,

Prepare and conduct Project Lesson Learnt (LL) for projects done,

Carry out any other related duties as required, including temporary assignments in other sections within the MTAC department on site.

Qualifications/Experiences Required

Educational Qualifications:

· Diploma/ Degree in Mechanical Engineering or related discipline

Technical Qualifications:

· Valid Certified Welding Inspector (CSWIP 3.1) or equivalent

· Qualified MOM OPSOC (Supervisor) or equivalent

· ASNT qualification is a bonus

Professional Experience:

· Minimum 20 years of relevant experience in oil & gas, chemical & petrochemical industry in the below fields:

o Project Quality Management Systems

o Brownfield construction

o Civil, Steel Structure, Piping/Pipeline Construction

o Application of Protective Coatings (Organic Coatings, fireproofing)

o Non-metallic piping systems.

· Relevant experience includes:

o Set up and execution of Project Quality Plan

o Workshop and field quality assurance and control

o Leading EPCm and Contractor quality teams in flawless delivery

· Experience in Plant Turnaround Project Quality planning, preparation and execution.

· Conversant with international codes and standards such as ASME II, ASME V, ASME VIII, ASME IX, ASMEB31.1, ASME B31.3, AWS D1.1, API 1104, API 650 & 620, ASTM, SHELL DEPs

• Facilitates planning and development ofquality control systems for specifiedproducts or processes.
• Collaborates with teams of engineers andproduct specialists to ensure customer anddivision quality requirements are met.
• Identifies the root cause of qualityproblems, and coordinates modificationsor other corrective actions.
• Liaising of Calibration Program.
• Periodically inspect instrument accordingto the specified schedule date
• Reviews design, manufacturing, and testingdocumentation.
• Update our Quality Management system(QMS) with incidents, fixes andimprovement.
• Offers technical guidance and support inresponse to quality testing and analysis.
• Ensures contract compliance by reviewingand approving quality requirements forsupplier purchase orders, manufacturing,and other related services.
• Performs other duties as assigned.

The Career Conversion Programme (CCP) (Train-and-Place with Commitment to Hire) for Advanced Biopharmaceuticals Manufacturing Executives/Professionals is a talent development programme aimed at building the next generation of skilled manpower for Singapore’s Biopharmaceuticals manufacturing industry in anticipation of hiring demand.

The training programme consists of 15 months of local attachment with GSK. Due to the nature of the programme, we can only consider Singapore Citizens and Singapore Permanent Residents. For more information, please visit Career Conversion Programmes (CCP) for Individuals

Purpose:

• To perform testing and support related activities in QC Biological team

Key Responsibilities:

• Perform routine and adhoc/ non-routine testing in the following areas with good observation of GMP requirements:
• Biological testings for raw materials release (All QA controlled materials). Biological testings refer to biochemistry and/ or microbiological testings.
• Biological testings for intermediates and product
• Biological testings for utilities (city water, purified water, water of injection, compressed gases, etc)
• Biological testings required to support manufacturing process validations and confirmations
• Perform routine environmental sampling in controlled environmental areas
• Initiate and participate in laboratory investigation (OOS / deviations / atypical results / invalid results) and assist in timely closure of the investigation and CAPA
• Perform equipment calibration, maintenance and validation
• Participate in method transfer / verification / validation
• Participate in peer review for verification of task and data
• Assist in SOP writing
• Identify and report problems in QC to QC Superintendent in a timely manner
• Practice 6S and ensure good housekeeping of laboratory, work area and equipment
• Ensure good inventory of QC materials (purchased and prepared materials / glassware) to support testings; ensure no over surplus of inventory
• Ensure wastes are disposed appropriately and promptly
• Adheres to all safety and security policies and practices
• Assist the Senior Superintendent/Superintendent in the management and operations of the team; may be indirectly responsible for a team of associates:
• Scheduling day-to-day shopfloor activities and resources handling to ensure timely availability of test results
• Reviews test reports to ensure accuracy of test results in accordance with corporate, regulatory and external agency regulations.
• Provides training to the team.
• Provides guidance, support and technical expertise to the team.
• Involves in investigation and protocol writing (when required)
• Involves in SOP writing and updating
• Organization and Problem Solving:
• Creates strong team morale and a culture of accountability and ownership
• Recommends and coordinates appropriate corrective actions to quality problems in conjunction with other teams/ departments
• Presents in timely manner major issues to the management with strategies on their resolution.

Skills:

Professional

• For QC Associate, fresh graduate in NITEC/ Diploma in Microbiology, Biotechnology, Life Sciences, Chemistry, Biochemistry
• For Senior QC Associate, NITEC/Diploma in Microbiology, Biotechnology, Life Sciences, Chemistry, Biochemistry, with at least 2 years of working experiences or Fresh degree holder in Microbiology Biotechnology, Life Sciences, Chemistry, Biochemistry. Increased number of years of experiences are required for higher positions.
• For Lead QC Associate, NITEC/Diploma in Microbiology, Biotechnology, Life Sciences, Chemistry, Biochemistry, with at least 8 years of working experiences or Degree holder in Microbiology, Biotechnology, Life Sciences, Chemistry, Biochemistry with at least 4 years of working experiences.

Technical

• Competent technical skills in the following:
• Good laboratory knowledge and hands-on experience in chemistry testings o Laboratory equipment qualification
• (advantage)
• Knowledge of cGLP & cGMP (advantage)

Business

• Effective report writing skills
• Planning and Organizing skills
• Effective team player
• Analytical skills with logical thinking
• Good interpersonal skills
• Leadership skills (advantage)

Competencies:

• Good command of English
• Good knowledge on usage of computers

Where will I be based?

You will be based at one of our manufacturing site in Singapore near Tuas.

The Career Conversion Programme (CCP) (Train-and-Place with Commitment to Hire) for Advanced Biopharmaceuticals Manufacturing Executives/Professionals is a talent development programme aimed at building the next generation of skilled manpower for Singapore’s Biopharmaceuticals manufacturing industry in anticipation of hiring demand.

The training programme consists of 15 months of local attachment with GSK. Due to the nature of the programme, we can only consider Singapore Citizens and Singapore Permanent Residents. For more information, please visit Career Conversion Programmes (CCP) for Individuals.

Purpose:

• To manage QC equipment life cycle from qualification to decommissioning including calibration and maintenance plan follow up

Key Responsibilities:

• Technical responsibilities
• Manage new QC equipment qualification as per change control and validation processes (i.e. URS, System classification, Audit trail review assessment, DQ/IQ/OQ, PPC09)
• Be author of SOPs/ protocols/ reports/ training materials
• Manage decomissioning of QC equipment and follow disposal
• process
• Maintain our QC asset listing up to date Follow QC equipment routine lifecycle
• Coordination of calibration and maintenance plan with user and external vendor/TS team
• Coordination of equipment troubleshooting if occurence of failure/breakdow (i.e. Tag in/out equipment, Work order creation)
• Sample transfer, alarm management and cleaning for fridges, freezers and incubators
• Liaise with external vendor for service quotation, escort vendor during service and approve invoice timely
• Supports compliance activities:
• Performs regular Ll audits in QC
• Coordinates and supports all L2, L3 and L4 audits and the associated CAPAs
• Lead and manage continuous improvement projects Subject-matter-expert (SME)/ audit fronter for assigned topics
• Manage ad-hoc tasks
• Organization and Management Responsibilities
• Creates strong team morale and a culture of accountability and ownership
• Provides leadership, guidance and technical expertise/support to the juniors
• Ensures continuous improvements of the QC operations
• Ensures expenditures are within budget
• Decision Making
• Proposals & Recommendations
• Based on experience & knowledge of work
• Proposal of CAPA for any issues/ deviations/ exceptions/ risks
• Proposal of QC improvement projects and strategies
• Team training and development

Skills:

Professional

• For Specialist - University Degree in a relevant Science discipline with at least 2 years of working experience or Diploma with at least 5 years of working experience
• For Senior Specialist - University Degree in a relevant Science discipline with at least 4 years of working experience or Diploma with at least 8 years of working experience

Technical

• Competent technical skills in project management
• Computer system validation Knowledge of cGLP & cGMP

Business

• Effective report writing skills
• Planning and Organizing skills
• Good interpersonal and communication skills
• Effective team player
• Analytical skills with logical thinking Problem solving skills

Competencies:

• Effective report writing skills
• Planning and organization skills
• Able to work independently
• Team player
• Analytical skills with logical thinking
• Leadership skills (advantage)
  ​​

Where will I be based?

You will be based at one of our manufacturing site in Singapore near Tuas.

The National Research Foundation (NRF) Medium Sized Centre for Advanced Robotics Technology Innovation (CARTIN) is a joint research center led by NTU with participation from NUS and ASTAR. The center has two research thrusts: Sentient Autonomy and Collaborative Autonomy, and focuses on developing advanced active perception and navigation, collaborative robotics and robots for humans technologies for applications in logistics, manufacturing, and elderly/health care.

CARTIN is looking for a highly experienced and motivated individual to join us a Research Associate to work on a NRF CARTIN project to conduct research on verification of resilience on sensing and control of multi-robot and human systems in a complex operational environment.

Key Responsibilities:

• Carry out literature research on STOA of verification of resilience.
• Develop a formal-method based modeling framework that can capture a variety of operational requirements and performance constraints under uncertain environment, upon which quantification of resilience of sensing and control is feasible.
• Develop an efficient analysis and verification method to evaluate degree of resilience and satisfaction of given requirements and constraints.
• Apply the developed modeling and verification methods in a (simulation/field) testbed for robotic sensing.
• To publish research results in reputable journals and conferences (in particular, ICRA).
• To assist project PI to coach research students.

Job Requirements:

• A Masters degree in relevant fields with past research foci on formal methods, modeling and analysis of complex operations under uncertain environment, control and optimization.
• A strong publication record in relevant fields. Relevant publications in human-robot systems will be a plus.
• Knowledge in modeling, simulation, and analysis of human-robot systems is a plus.

We regret to inform that only shortlisted candidates will be notified.

Established in 2010, the Energy Research Institute @ NTU (ERI@N) is a pan-university research institute that focuses on systems-level research for tropical megacities. It performs translational research that covers the energy value chain from generation to innovative end-use solutions, motivated by industrialisation and deployment. ERI@N has multiple Interdisciplinary Research Programmes which focus on translational Research, Development & Deployment which focus on specific area of the energy value chain, and a number of Living labs and Testbeds which facilitate large scale technology deployment enabling validation and demonstration of real-world applications.

For more details, please view https://www.ntu.edu.sg/erian

To support the research project titled:

• Technology Development of Thermal Management, Lifetime Assessment and Prognostics for Li-ion Battery Energy Storage System in Next-Generation Grid
• Design and Development of Compact Energy Storage System
• Design and Development of ESS coupled with solid state transformers

This job position is required for recruiting a highly educated and experienced researcher with experience to develop battery management system for lithium-ion battery packs in energy storage system application. It will also fulfil the objective of NTU in developing energy storage system and novel renewable energy technologies.

Key Responsibilities:

• Develop overall battery management scheme according to system performance requirement
• Design and develop software of battery management system
• Design and develop hardware and PCB layout of battery management system
• Design and develop state estimation algorithm of battery management system
• Design and develop balancing control strategy of battery management system
• Conduct simulation test and debug of developed software of battery management system
• Conduct simulation test, layout design, PCB design, manufacturing, and testing
• Conduct simulation test of the designed algorithm, balancing strategy.
• Responsible to prepare design progress document and final project report

Job Requirements:

• Masters degree in electronics, control, electrical, or similar
• Research or working background in lithium-ion battery product development and production is a must.
• Experience in technology development for lithium-ion battery management system is required.
• Candidate must be familiar with design requirements on control, state estimation, balancing of battery packs
• Familiar with software like Matlab/Simulink, Keil, CodeWarrior, Altium Designer.
• Understand development progress of battery management system product
• Self-motivated and takes initiative
• Independent and can work well with a team
• Organized and detail oriented
• Excellent verbal and written communication skills

We regret to inform that only shortlisted candidates will be notified.

Job Responsibilities:

• Support continuous improvement efforts in QMS.
• Support in root cause analysis and implementation of corrective/ preventive actions for process related concerns.
• Analyze and provide timely respond to customer complaints.
• Interface with Customer and Operations to ensure new product transfer to manufacturing are in accordance with approved requirements.
• Prepare Quality performance metrics and reports.

Requirements:

• Diploma in Mechanical Engineering, Quality, or equivalent.
• Minimum 2 years work experience in Quality Management System in manufacturing environment.
• Good knowledge of ISO 9001. Knowledge of API Q1 is preferred.
• Strong command of English language, both oral & writing.
• Knowledge of metal working industry is preferred.
• Knowledge of risk assessment principles and methods.
• Knowledge of SAP is preferred.
• Positive & proactive attitude.

Job Responsibilities:

• Support continuous improvement efforts in QMS.
• Support in root cause analysis and implementation of corrective/ preventive actions for process related concerns.
• Analyze and provide timely respond to customer complaints.
• Interface with Customer and Operations to ensure new product transfer to manufacturing are in accordance with approved requirements.
• Prepare Quality performance metrics and reports.

Requirements:

• Diploma in Mechanical Engineering, Quality, or equivalent.
• Minimum 2 years work experience in Quality Management System in manufacturing environment.
• Good knowledge of ISO 9001. Knowledge of API Q1 is preferred.
• Strong command of English language, both oral & writing.
• Knowledge of metal working industry is preferred.
• Knowledge of risk assessment principles and methods.
• Knowledge of SAP is preferred.
• Positive & proactive attitude.

Key Responsibilities

The successful incumbent will support the QA Manager in the following responsibilities.

• Ensure compliance with the Company’s food safety management system, QA standards, customer requirements, certification audits, and regulations for quality and food safety control processes.
• Support the Quality Assurance Manager (QAM) in preparing external and internal audits according to customer standards/contract requirements, and drive cross-functional teams to achieve targeted performance.
• Conduct site inspections to promote continuous improvement and adherence to Standard Operating Procedures (SOPs), hygiene, and food safety practices.
• Manage QA random sampling and microbiological testing for food samples, raw materials, water & ice, hand swabs, and Environmental Monitoring Program (EMP).
• Analyze data and follow up on unsatisfactory test results to identify potential causes of failure, recommend corrective actions for process improvement, and prevent recurrence.
• Prepare documentation related to all export matters in the capacity of Quality Person (QP).
• Develop training materials and conduct food safety trainings for operational staff.
• Review new product artwork to ensure regulatory compliance.
• Assist QAM in food safety incident management, including site investigations, testing, and preparation of incident reports.
• Support QAM in maintaining the ISO 22000/HACCP manual and QA documentation.
• Assist in the supplier approval program (supplier assessment/documentation review).
• Contribute to QA work plans and initiatives aimed at improving QA processes and food safety standards.
• Support Group QA, annual emergency exercises, and ad-hoc catering events as required.

Key Requirements

• Minimum Degree in Food Science/ Technology or other relevant fields.
• Minimum 2 year of QA experience in the food industry.
• Passionate in upholding food safety and possess good knowledge of Food Regulations, SFA requirements, GMP, and food safety management certifications (e.g., HACCP, ISO 22000, GFSI standards).
• Keen learning attitude, proactive, and decisive.
• Detail-oriented and meticulous with competency in report writing and presentation skills.
• Independent, committed and possess strong interpersonal communication skills
• Ability to multi task, handle stress in a fast-paced environment, and meet tight deadlines.
• Excellent interpersonal and communication skills.
• Collaborative and able to work effectively in a team.
• Must be comfortable working in a cold environment.

The Career Conversion Programme (CCP) (Train-and-Place with Commitment to Hire) for Advanced Biopharmaceuticals Manufacturing Executives/Professionals is a talent development programme aimed at building the next generation of skilled manpower for Singapore’s Biopharmaceuticals manufacturing industry in anticipation of hiring demand.

The training programme consists of 15 months of local attachment with GSK. Due to the nature of the programme, we can only consider Singapore Citizens and Singapore Permanent Residents. For more information, please visit Career Conversion Programmes (CCP) for Individuals

Purpose:

• To be responsible for managing the interactions with third party organisations that supply QA incoming materials and/or services to GSK.
• To manage material release for incoming materials, supplier change notifications and new material management.
• To provide Quality oversight to logistics management and warehouse operations.

Key Responsibilities:

Supplier Management

• Provide QA oversight of Supplier management activities on site to achieve compliance with company policies and government regulations as assigned.
• To participate (Executive 1) and to represent the site (Executive 2) for Supplier Management business processes to drive improvements and share best practises across the GSK Vaccines network.
• Process owner/support supplier complaint process for QA incoming materials. Lodge supplier complaints and ensure suppliers identify the root cause and associated CAPA's to prevent recurrence of supplier quality issues.
• Review and track supplier-related CAPA for timely closure.
• Maintain inspection readiness, conduct supplier assessments for both new and current service providers in a timely manner.
• Maintain the approved supplier listing and audit schedule in a state of compliance and accuracy.
• Assess supplier change notifications in a timely manner and escalate where necessary especially in situations with supply impact.
• Initiate and review deviations/change control/CAPA associated with incoming material.

Executive 1: Minor deviations and CAPA

Executive 2: Minor, major deviations and CAPA

• Work closely with site user and Global stakeholders for Supplier management related matters

QA Raw Material Release and Warehouse oversight

• Support incoming material documentation review and release to recommend and confirm Usage Decision (UD) of raw material
• Ensure that material document file (MDF) is complete and accurate before disposition of material in SAP
• Ensure that system is in place for filing and archival of MDF
• Initiate and review deviations/change control/CAPA associated with incoming material releases.
• Ensure that all deviations/change controls are closed or assessed for impact on the release of the material prior to release the QA-controlled incoming material
• Provide QA oversight to warehouse such as attending warehouse tier, conduction GEMBAs, inspection readiness and warehouse related deviations, CAPAs and change control

Decision Making:

Proposals & Recommendations

• Propose improvements to work processes, with basic awareness of business requirements.
• Deviation investigations and assessments
• In addition for QA Executive 2:
• Able to provide QA oversight on routine situations independently and complex situations with supervision (deviations, changes, system issues, compliance matters)
• Able to manage simple department projects (e.g. continuous improvement) with supervision
• Greater awareness of business requirements and to highlight considerations where there is a need for escalation

Skills:

Professional

• At least University basic degree in a Science or Engineering discipline

Technical

• A good understanding of cGMP regulatory and legal requirements as applied to quality assurance of pharmaceuticals manufacturing
• User experiance with SAP will be prefered
• Ability in handling and organizing multiple workflows

Business

• Ability to apply optimal quality assurance standards to promote a business edge
• Ability to facilitate business activities commpatible to international regulatory environment
• Ability to communicate effectively within the site organization and across the network

Competencies:

• Working knowledge of FDA/EU/ICH/WHO as well as all other relevant reuglatory and technical guidelines
• Possess Analytical and Quality performance mindset
• Demonstrate professional & ethical integrity
• Fluency in the English language
• Demonstrates sense of urgency
• Ability to work both as an individual contributor and as a team player.

Where will I be based?

You will be based at one of our manufacturing site in Singapore near Tuas.

Job description

Non-Destructive Testing (NDT) technicians examine structures,vehicles, and products for flaws and structural weaknesses usingnon-destructive testing techniques. They conduct material tests,interpret the results, and generate reports on their findings.

Requirements

Bachelor's degree in mechanical engineering, structural engineering,or a similar field.

Relevant NDT certification.

10+ years' experience as an NDT technician.

Advanced knowledge of NDT technologies including ultrasound,infrared, and radiographic.

The Career Conversion Programme (CCP) (Train-and-Place with Commitment to Hire) for Advanced Biopharmaceuticals Manufacturing Executives/Professionals is a talent development programme aimed at building the next generation of skilled manpower for Singapore’s Biopharmaceuticals manufacturing industry in anticipation of hiring demand.

The training programme consists of 15 months of local attachment with GSK. Due to the nature of the programme, we can only consider Singapore Citizens and Singapore Permanent Residents. For more information, please visit Career Conversion Programmes (CCP) for Individuals.

Purpose:

• To manage logistic activities within QC department

Key Responsibilities:

• Performs receipt and storage of sample in accordance to local procedure.
• Performs routine and non-routine sampling of raw materials and utilities with observation of GMP requirements
• Ensures proper packaging of samples and correct samples are shipped to offsite recipient timely
• Ensures a good inventory of QC materials (purchased and prepared materials/glassware) to support testings; ensures no over surplus of inventory
• Ensures wastes are disposed appropriately and promptly.
• Practices 6S and ensures good housekeeping of laboratory, work area and equipments.
• Supports equipment calibration and maintenance, performs autoclave requalification and washing machine verification
• Performs peer review for verification of task and data.
• Participates in laboratory investigation (when required) and assist in the timely closure investigations, CAPAs.
• Ensures proper archival of submitted document for easy retrieval
• Identifies and reports problems in QC to supervisor in a timely manner.
• Adheres to all safety and security policies and practises
• Manages ad-hoc support tasks
• Assist QC support manager in the management and operations of the team
• Scheduling day-to-day shopfloor activities and resources handling to ensure timely sample and material management Provides training to the team
• Provide guidance, support, and technical expertise to the team Involves in investigation and protocol and report writing (when required).
• Involves in SOP writing and updating.
• Organization and Management Responsibilities
• Creates strong team morale and a culture of accountability and ownership
• Provides leadership, guidance and technical expertise/support to the juniors
• Ensures continuous improvements of the QC operations
• Ensures expenditures are within budget

Skills:

Professional

• For QC Support Technologist - Fresh graduate of NITEC, Diploma in Science (or equivalent)
• For Senior QC Support Technologist Graduate of NITEC, Diploma in Science (or equivalent) with at least 4 years of experience/Degree holder with at least 2 years of working experience.
• For Lead QC Support Technologist Graduate of NITEC, Diploma in Science (or equivalent) with at least 8 years of experience/Degree holder with at least 4 years of working experience.

Technical

• Competent technical skills in good laboratory knowledge and hands on experience in inventory management
• Knowledge of cGLP & cGMP

Business

• For QC Support Technologist, Senior QC Support Technologist 1, 2
• Basic report writing skills (preferably with legible hanwriting)
• Basic planning and organizing skills (for individual time management and work planning) Good interpersonal skills
• Team player
• For Senior QC Support Technologist 3 and Lead
• Effective report writing skills
• Planning and organizing skills (for individual time management and work planning)
• Leadership and problem solving with analytical and logical thinking

Competencies:

• Effective report writing skills
• Planning and organization skills
• Able to work independently
• Team player
• Analytical skills with logical thinking

​​

Where will I be based?

You will be based at one of our manufacturing site in Singapore near Tuas.

Job Description & Requirements

Able to operate CNC CMM machine with 2 years experience needed is a priority.

Knowledge in QC equipments, example: Height Gauge, Smart Scope, Veriner caliper etc.

With computor knowledge to provide QC report and handle NCR.

Must have knowledge in drawing specification. Example: Tolerance, Surface Treat, Heat Treat etc.

Basic knowledge in machining process.

Job Description:

1. Performing F.A inspection and inspection of parts and products with desktop measuring tools / CMM / Smart scope at the incoming / outgoing / in-process gate.
2. To prepare and generate standard inspection report and lead team in performing quality inspection.
3. Monitor on critical customer products, with a corrective and preventive action programs in managing customer complaints / improvement plans.
4. Administer and work on continuous improvement program in achieving good process control.
5. Provide technical guidance to group of inspectors.
6. Manage customer complaints, corrective and preventive action programs.
7. Work closely with customers and inter-department to meet the quality requirements.
8. Experience in calibrating measuring equipments.

Requirements

• Preferred to have NTC / Diploma in related engineering field.
• Required to know-how in using desktop measuring tools, and other equipment such as CMM, Smart Scope, Roundness Tester and Roughness Tester
• Computer competancy.

Job Responsibilities:

• Management of Quality Management Systems.
• Support and maintain relevant systems both internally and externally.
• Responsible for Documentation Control system and Audits.

Job Requirements:

• Good working experience.
• Precision manufacturing industry.
• Adequate understanding of Quality Management System.
• Team player with good initiative and proactive.
• Microsoft office.

Job Description

1. Supervise a team of QC Officers in all factories.
2. Guide and troubleshoot for any equipment issues, co-ordinate with external service providers Ensure laboratory equipment is calibrated in a timely manner and update calibration records. Assist to keep, control, and confirm formulation and blending procedures.
3. Respond to new and existing customers for inquiries related to quality control Conduct quality testing and communicate product specification issues. Conduct nonconforming material or nonconforming product analysis.
4. Participate in the root cause analysis of nonconforming goods.
5. Follow the instructed corrective actions and preventive actions by superiors. Establish formulation and blending procedures as needed.
6. Keep and monitor retain samples of products
7. Validate COA of raw materials received and communicate any issues to the procurement and Plant Manager Establish, update and issue GHS SDS.
8. Create certificate of analysis (COA) of products.
9. Confirm and provide resources for the laboratory and other QCR needs.
10. Coordinate sample delivery as required by the customer.

Job Requirements

• Min. Degree in Chemistry related field or
• Diploma in Chemistry with minimm 5 years of relevant experience
• Technical Knowledge : Microsoft Officer (Basic) / Good knowledge & skills on QC testing
• Ability to coach and mentor the team

Element has an opportunity for an experienced Quality Engineer. Reporting to the Principal Quality Manager, you are an essential member of the management team and responsible for the overall quality performance. This includes implementation, maintenance and improvement of Element quality management system (QMS). The successful candidate will have a sound working knowledge of ISO/IEC 17025, ISO/IEC 17020 or ISO/IEC 17065 requirements in relation to testing, calibration inspection and certification.

In this role, you will have interaction with clients, Accreditation Bodies and will be responsible for advising operational colleagues of the importance of quality, accuracy and integrity in the provision of the testing, calibration inspection and certification services we provide.You will be involved in leading quality at a local level and will work closely with the Principal Quality Manager to ensure that Element quality policies, processes and procedures are effectively implemented. As a quality leader within Element you will be capable of driving a culture of quality assurance and quality improvement, working closely with your operational colleagues and the wider Element quality community.

This role is based in Sungei Kadut Loop, Singapore.

Job Duties:

• Ensuring all staff buy-in to the effective and efficient implementation of Element quality policies and procedure by providing advice, guidance and support on quality issues to Element Singapore and Malaysia business units.
• Driving quality improvements at every opportunity and proactive participation in continuous improvement and process improvement projects and ensure effective adoption of Element e-QMS throughout Element Singapore and Malaysia business units.
• Proactive participation in projects to deliver identified Quality objectives and contribute to and drive key initiatives to improve Quality awareness and compliance.
• Management of and participation in scheduled internal audits across management system and technical disciplines and proactively monitoring laboratory test equipment for calibration currency and advising management of upcoming schedules,ensuring corrective and preventive actions identified within specific laboratories are implemented and verified in a timely manner.
• Represent Element Singapore and Malaysia business units during assessments by accreditation bodies and audits by clients and controlled document holding and arrange to update appropriate documentation as necessary, control and issue of Element Singapore and Malaysia Quality Management Systems documentation and participate in the internal audit programme to monitor implementation of quality policies and procedures.
• Manage external and internal proficiency testing programs of all Element Singapore and Malaysia business units and prepare compliance and improvement metrics for Element Singapore and Malaysia business units quality as required.
• Writing and reviewing quality documentation as required and effective and efficient management of personal work schedules and timely generation of Element Singapore and Malaysia business units quality reports.

Job Requirements:

• Minimum Bachelor of Science or Engineering qualification.
• Proven experience (minimum two years) of managing quality management systems within a multi-discipline testing, inspection and certification environment, preferably multi-location.
• Demonstrable experience auditing against ISO/IEC 17025, ISO/IEC 17020 and ISO/IEC 17065.
• Sound knowledge of equipment calibration and analysing proficiency test data.
• Knowledgeable in uncertainty of measurement and risk assessment and hands-on experience with Element e-QMS preferable.

HOW TO APPLY:

Interested applicants, please submit your updated resume to [email protected]

Please state your availability, current & expected salaries for processing purpose. All applications will be treated in the strictest confidence. We regret that only shortlisted candidates will be notified.

• MEP Contractor
• Basic up to $5000
• Office hour 6 days
• Bus from MRT Pioneer

Job Responsibilities:

• Oversee quality checks for incoming, in-process, and outgoing products, ensuring adherence to inspection criteria, quality plans, and finishing work per method statements.
• Work with QA, Process, Engineering, and Product teams to address quality issues, perform audits, and implement corrective actions.
• Manage and control supplier quality standards, ensuring compliance with required specifications.
• Prepare inspection reports, coordinate site visits, and liaise with Project Managers, Engineers, and Authorities for certifications.
• Provide training to workers on method statements and ensure compliance with construction and quality standards.

Job Requirements:

• Minimum ITE, Diploma, or Degree in Manufacturing or Quality Engineering.
• Preferably at least 2 years of experience in a Product Manufacturing environment.
• Knowledge of ISO standards (9001, 14001, 13485, 45001) is a plus.
• Understanding of quality requirement of DMA Modular Prefab MEP product, Materials Selection, Fabrication, Assembly and Inspection will be an advantage.

For consideration, kindly submit your CV by clicking “APPLY NOW” or email to [email protected] for confidential discussion.

*Only shortlisted candidates would be notified**

MTC Consulting Pte Ltd | 15C7752

EA. Registration No.: R24124448 | Nana Yeoh Li Xuan

Hiap Tong Crane & Transport is hiring Credit Control cum Administrative Assistant.

Job scope:

- In charge in calling & liaise with customers to follow up on outstanding payment

- Prepare monthly Statement of Accounts & payment reminder to customers

- Maintaining accurate records of customers' payment history and debt recovery efforts

- Assist in Generating and Sending invoices to customers

- Office administrative & clerical works

- Any other ad-hoc tasks as assigned

Requirement:

- Competent in Microsoft office application

- Possess good working attitude & sense of responsibility

- Excellent communication and negotiation skills

- Strong understanding of credit risk assessment and collections processes

- Detail-oriented, organized, and capable of meeting deadlines.

- Ability to work independently and as part of a team

- At least 01 year of proven experience as a Credit Controller or similar role in finance/accounting