Description

• Perform troubleshooting, service & calibration work both at site & in-house
• Performs periodic, predict, preventative, repair and maintenance services for Company’s equipment and associated controls
• Overhaul, install, calibrate control valves and field instruments
• Supervising & managing of Sub-contractor to carry maintenance & servicing works
• Record servicing & maintenance data and generate service report

Requirements :

• Possess NITEC/Higher NITEC/Diploma in Mechanical / Mechatronics Engineering
• Communicate effectively, Customer orientation, Flexibility and self learning
• Can do attitude, Teamwork
• Energetic and good interpersonal skills
• Candidate without experience are welcomed to apply

We regret that only shortlisted candidate(s) will be contacted.

• Candidate must possess at least Bachelor's Degree/Post Graduate Diploma/Professional Degree in Engineering(Civil) or equivalen.
• At least 2 years(s) of working experience in the related field is required for this position.
• Required Skill(s): Understand drawing, Quantity take off, Prepare BQ, Familiar with costing, Supplier sourcing, Contract administration.
• Preferably Senior Executive specialized in Engineering-Civil/Construction/Structural or equivalent.
• Familar with structural steelworks.
• Other QS duties as assigned from time to time.

Job Description & Requirements

.Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

Job Description & Requirements

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection.

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Job Description & Requirements

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Job Description & Requirements

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Job Description & Requirements

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Job Description & Requirements

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Job Description & Requirements

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

Job Description & Requirements

Review the inspection history to summarize the integrity status of the plant equipment and piping systems.

· Perform the scoping work and prepare the job pack for process piping and in-service equipment based on engineering assessment and annual inspection plan.

· Plan and carry out fixed equipment/piping inspection via on-stream risk-based monitoring programs and downtime inspection activities including corrosion under Insulation (CUI) and corrosion under pipe support (CUP) on process piping and equipment according to annual maintenance plan

· Identifying the areas of special concern and deterioration (e.g. Dead legs, injection points, mix points, corrosion under insulation and Low silicon Inspection).

· Supervision and coordination of all on-stream and shutdown inspection and NDT activities for static equipment and in-service process piping.

· Review of inspection test plan, WPS and method statement for any in-service repair work of piping and pressure vessels.

· Witnessing of PT, MPI, PMI, metallographic tube testing and Hydro static test for statutory equipment.

· Provide recommendations and timely updates on equipment degradation problems.

· Provide quality assurance on project construction and maintenance works to ensure compliance with applicable codes, standards and specifications.

· Preparation of final inspection reports with all findings, abnormalities and recommendations.

· Ensure quality of inspected items to meet project requirements and standards.

· Inservice inspections in refineries / Oil and Gas / Petrochemical industries, such as corrosion under pipe support (CUPS), corrosion under insulation (CUI), Injection & Mix points inspections.

· Read, understand project related ITP, procedures, specification requirements.

· Review documents and drawings as per specification • Knowledge / experience about Piping Isometrics, P & ID, general arrangement drawings, Structural drawings, Weld Maps, welding symbols, Cutting Plans, Quality control procedures, Base Materials, and welding consumables.

· Inspection, review of mill certificates, Material verification, Inspection of Pipes, Fittings, Flanges, valves, nipples, plate tubes as per respective materials specifications, Codes, Standards & Client Specifications. Inspection / Witness & Review Stage wise activities earlier stage of spool fabrication

· Knowledge in welding inspection

Eligibility Criteria

· Graduate Engineers with 3-6 years of relevant experience.

· Relevant Engineering Degree or Diploma in Mechanical, Petroleum/Oil/Gas, Civil, Chemical or Industrial Engineering are acceptable.

· Experience in Refinery and Oil & Gas must

· Experience in QA/QC and Knowledge in Non-Destructive Testing methods.

· Knowledge/experience in welding inspection, structural fabrication, piping Isometric drawing and piping materials.

· Work Independently and can work in Singapore and other countries.

· Fluent Reading, Speaking and Writing in English.

· Willing to commit 24 months contract/ project completion.

· Team Worker, Mature, Meticulous, Pro-Active Work Attitude & Work Independent.

· Energetic & Result Orientated.

· Perform incoming, in-process and outgoing quality control activities

· Liaise with customers pertaining product specifications and quality issues

· Update quality standards regularly in order to conform to customer’s requirements

· Perform in-coming, in-process and final QC daily activities

· File and update QC testing records or reports

· Review and verify daily routine QC results

· Liaise with Logistic Coordinator to arrange for outgoing shipment activities

· Report abnormalities to QA Supervisor

· Prepare quality related reports

· Take part in ISO 9001:2015 IQA activities

Any other duties and responsibilities assigned by the Company from time to time

Work Place : Pasir Ris (2 weeks training @ Woodlands)

Working Day : 5.5 days

Working Hour : 8.30am to 6pm, 8.30am to 12.30pm

OT available

Roles & Responsibilities

Job Description:

Prepare and analyze cost comparison

Obtaining quotations, liaising and negotiate with sub-contractors and suppliers

Responsible for measuring quantities and taking off

Prepare Variation Orders, claims, final accounts, settlement and sub-contractor payments

Prepare tender and contract documents, including bills of quantities with the architect and/or the client.

Undertake cost analysis for repair and maintenance project work

Assist in establishing a client’s requirements and undertake feasibility studies

Perform risk, value management, and cost control

Identify, analyze and develop responses to commercial risks

Prepare and analyze costings for tenders

Allocate work to subcontractors

Provide advice on contractual claims

Analyze outcomes and write detailed progress reports

Value completed work and arranged payments

Maintain awareness of the different building contracts in current use

Understand the implications of health and safety regulations.

All other QS related job

Job Requirements:

Degree / Diploma in Constructions Building or its equivalent

Ability in contract negotiation, contract administration & variation orders

Able to work independently, be meticulous, analytical with excellent problem-solving skills, proactive, a good team player & able to meet tight deadlines

· Attend to enquiries/complaints of customers (service or product failure) via email or phone and refer to appropriate personnel to follow up.

· Prepare servicing/maintenance and installation quotation & prepare maintenance contracts for customers.

· Coordinate and liaise with customers, technicians and contractors on installation and service maintenance.

· Resolve installation and service issues by clarifying with customer to determine the cause of the problem and provide appropriate support.

· Collection of outstanding payment, if any.

· Plan and allocate Technicians for jobs and ensure accurate service records in timely manner.

· Maintain and build good rapport with customers and technicians to expand customer base.

· Ensure that all repair and servicing orders are accounted for, monitored, and completed timely.

· Any other Ad-hoc duties as and when required

Responsibilities:

• Conduct regular vulnerability scans and assessments on networks, applications, and systems.

• Analyse scan results, prioritize vulnerabilities based on risk, and recommend remediation actions.

• Design, implement, and manage security measures for network infrastructures.

• Monitor network traffic for unusual or suspicious activity and respond to security incidents.

• Stay up to date with the latest security threats, vulnerabilities, and mitigation

techniques.

• Analyse potential threats and vulnerabilities to recommend proactive measures.

• Work closely with teams to ensure security best practices are integrated into

all systems and processes.

• Assist in the development of security policies and procedures.

• Prepare detailed reports on security incidents, vulnerabilities, and remediation efforts.

• Maintain documentation of security protocols and incident responses.

Requirements:

• Degree/Diploma in Information/Data/application security

• Proficiency in security assessment tools (e.g., Nessus, Qualys, Burp Suite, Metaspoilt) is mandatory.

• Strong understanding of network protocols, firewalls, VPNs , IDS/IPS, and

security best practices.

• Experience with incident response and security incident management.

• Familiarity with compliance frameworks (e.g., NIST, ISO 27001, PCI-DSS).

• Knowledge of scripting languages (Python, Bash, etc.) for automation tasks.

• Candidates must be able/well verse in Speaking, Writing, Reading in Mandarin and English

Co-ordinate on quality matters with project team, conduct regular inspection to ensure works are in compliance with method statements & proper sequence of work and in accordance to BCA's good industry practice.

Ensure that all project quality records and quality audit plans are maintained, assist in yearly ISO audit.

Prepare Quality Control Plan, procedures and QA/QC reports.

Inspect the final output, comparing it to the requirements and approving or rejecting the final products.

Knowledge of welding inspection and ISO standards, familiar with CONQUAS, Green Mark and other essential BCA requirements.

In-depth knowledge of quality control procedures and legal standards.

Good verbal and written communication skills.

Willing to travel to various sites.

Prepare Inspection Test Plan (ITP).

Prepare document submission for client's approval.

Compile and receive relevant material certificates and test report from suppliers.

Co-ordinate with relevant testing laboratories for material testing and witnessing.

Assist the project team on QA/QC matters.

Good understanding of construction industry practices and standards in particular metal works and facade works.

Degree / Diploma in Civil Structural Engineering or equivalent.

Minimum 2 years relevant experience in metal work and facade industry.

Co-ordinate on quality matters with project team, conduct regular inspection to ensure works are in compliance with method statements & proper sequence of work and in accordance to BCA's good industry practice.

Ensure that all project quality records and quality audit plans are maintained, assist in yearly ISO audit.

Prepare Quality Control Plan, procedures and QA/QC reports.

Inspect the final output, comparing it to the requirements and approving or rejecting the final products.

Knowledge of welding inspection and ISO standards, familiar with CONQUAS, Green Mark and other essential BCA requirements.

In-depth knowledge of quality control procedures and legal standards.

Good verbal and written communication skills.

Willing to travel to various sites.

Prepare Inspection Test Plan (ITP).

Prepare document submission for client's approval.

Compile and receive relevant material certificates and test report from suppliers.

Co-ordinate with relevant testing laboratories for material testing and witnessing.

Assist the project team on QA/QC matters.

Good understanding of construction industry practices and standards in particular metal works and facade works.

Degree / Diploma or equivalent.

Minimum 2 years relevant experience in metal work and facade industry.

Job Description:

• Manage the procurement activities of direct materials, including review and convert Purchasing. Requisition (PR) into Purchase Orders (PO); resolve invoice, or quality related discrepancies.
• Sending requirements to suppliers : Request for Quote (RFQ), Request for information (RFI) using digital tools.
• Purchase price analysis and price negotiations; Identification and realization of savings potentials,
• Close cooperation with the stake holders and suppliers.
• Supplier management including supplier set up, supplier evaluation and development.
• Optimization of existing supply chain processes and participation in project teams.
• Leverage existing procurement processes and compliance while seeking to identify best management practices. Using a continual improvement mindset to create efficient processes.

We are looking for:

• Degree in Industrial Engineering, Business Management, Economy or similar areas,
• +4 years professional experience in a similar position,
• Knowledge of Procurement / Supply Chain activities with a broad solid understanding of operational, activities across a range of businesses.
• Previous experience of working in Supply Chain Management
• Good knowledge of MS Office and SAP
• Fluent in English (written and spoken); Strong communication and negotiation skills;

Job duties and responsibilities:

• Design new products and continually improve existing products to meet industry standards and customer requirements.
• Develop technical manuals and Instruction Operating Manuals for products, ensuring accuracy and usability.
• Prepare, review, and verify design drawings, detailed specifications, and fabricated drawings for compliance with technical standards.
• Create Bills of Materials (BOMs) and ensure accurate documentation.
• Order materials and supplies; monitor the progress of fabrication and installation to ensure alignment with design specifications and schedules.
• Perform quality control checks to ensure the integrity of materials, components, and final products.
• Update and maintain design records, project databases, and documentation for traceability and reference.
• Track and coordinate the delivery of goods and materials to meet project timelines.
• Collaborate with cross-functional teams, including procurement, production, and project management, to address technical challenges.
• Provide technical support and guidance to the fabrication and installation teams during project execution.
• Identify opportunities for cost optimization, design innovation, and process improvement.

Job Requirements:

• Degree or Diploma in Mechanical, Precision, Tool, and Die Engineering, or a related field.
• At least 2 years of experience as a Design Engineer.
• Proficiency in drafting software such as AutoCAD, SolidWorks, 3D modeling software, or equivalent.
• Experience in Marine Hydraulic Applications, with knowledge of valves and actuators, as well as gear design (e.g., spur gear, planetary gear, bevel gear).
• Understanding of forging, casting, and precision CNC machining processes.

Job Duties and Responsibilities:

• Provide technical support to resolve technical inquiries from ships/vessels on Nordic Systems.

• Attend on-board service attendances and commissioning services, annual inspection and maintenance for vessels based on troubleshoot of the technical issues and feedback by chief engineer/vessel managers.

• Review service reports, customer technical specifications and provide support to sales team for bidding of spares.

• Troubleshoot issues involving electrical/electronic control systems, PLC products.

• Read and understand manuals, schematics, and P&ID's.

• Lead the preparation and coordination of ITRs based on approved electrical completion procedures.

• Prepare and update status of punch list and ensure all cleared punch items to be acknowledged by the client reps.

• Monitor and manipulate site execution in line with sequence of works.

• Handle technical issues, drawings, reports, procedures and any other relevant documents.

• Develop engineering capabilities and work with sales team on project proposal and bidding.

• Selection of equipment, materials for instrumentation and controls.

• Execution of projects.

• Plan and carry out E&I maintenances

• Manage Subcon and other adhoc activities, lead the team of technicians on site to execute the project.

Job Requirements

• Candidate must possess at least a Diploma, Advanced/Higher/Graduate Diploma, Degree, Post Graduate Diploma, Professional Degree, Engineering (Electrical/Electronic) or equivalent.

• Prior experience in the Maritime/Oil & Gas industries and shipyards will be highly advantageous.

• Excellent verbal and written communication.

• Possess excellent interpersonal and communication skills.

• Responsible, Meticulous and able to work under pressure.

• Proficient with Microsoft Office Applications (Outlook, Word, Excel, Power Point, etc).

• Experienced in PLC/SCADA systems.

• Fluency in English (verbal and written) is essential.

Job Duties and Responsibilities:

• Integrate and commission a variety of instrumentation and control systems for commercial projects.
• Program and integrate control systems, design control panels and subpanels, and generate I/O lists.
• Perform engineering tasks, including PLC and SCADA software interface programming.
• Develop process functional designs, including control write-ups and control schematics.
• Create hardware and software design specifications, as well as other software/test documentation.
• Diagnose and resolve issues in electrical, instrumentation, and control systems.
• Manage multiple tasks effectively, work under pressure, and meet tight deadlines to ensure timely completion of commissioning activities.

Job Requirements:

• Proven experience in PLC control program design and implementation within industrial or marine automation, or process automation settings.
• Strong technical knowledge and hands-on programming skills with various PLC brands.
• Proficient in technical knowledge and programming of SCADA software.
• Resourceful and highly organized, with excellent time management and problem-solving skills.
• A collaborative team player who can also work independently in a fast-paced environment.

Purpose of Position

• Provide maintenance and engineering support for process control systems to ensure safe and reliable operation of the plant.
• Provide technical and engineering support for projects and modifications related to control system to achieve business and operational objectives.

Principle Responsibilities

• Responsible for the maintenance and engineering of all process control systems which may be installed in the plant or externally at customers' site.
• Perform fine-tuning, troubleshooting, modification and programming of the Control System as needed to improve system performance and optimize process operation needs.
• Response to 24-hour emergency call-out and provide night-shift support during plant startup, shutdown and as requested by Operation Team.
• Work closely with the Instrument Team to troubleshoot and resolve instrumentation problems.
• Work with the Project Team to develop requirements and/or specifications of control system for projects and modifications; supervise & implement the project works according to the schedule and requirements.
• Plan and execute preventive and corrective maintenance works for plant turnaround.
• Perform strategy planning for control system expansion, upgrading and renewal.

Job Requirements

• Familiar and hand-on with the engineering tools and programming languages of control systems (Honeywell, Siemens PCS7 and Triconex), able to make program modifications and configuration changes confidently.
• Experienced and familiar with various phases of project works such as engineering, fabrication & construction and commissioning.
• Knowledge and experience with computer system networking, server/client and virtualization architectures.
• Degree in Electronics/Electrical Engineering, major in Control is preferred.
• Minimum 5 years relevant experience working and maintaining Honeywell DCS, Siemens PCS7, Triconex PLC and etc.

Job Description

• Review, track & monitor the main contractors’ programmes and/or CAG/CAAS direct contractors’ programmes to comply with CAG requirements.

• Review the main contractors’ baseline S-curve, cost loading, resources allocation, histograms and 4D BIM, highlighting areas of concern to SO/SO(Rep).

• Review and give detailed feedback on main contractors’ schedule submissions and recommend status of approval / non-approval to the SO/SO(Rep) in compliance with CAG requirements.

• Prepare monthly dashboard reports to CAG in relation to the progress of works and any issues that may negatively impact on the timely completion of the contract including presentation to stakeholders, if any.

• Review main contractors’ progress reports.

• Review main contractors’ updated programmes which reflects the actual progress of works and capture any change of work sequence.

• Keep record of important site information such as, equipment and manpower deployment, changes to any design/construction dates, delay events, etc.

• Review and assess trade productivities.

Job Requirements

• The Planner shall possess at least ten (10) years of relevant construction experience with at least 7 years of experience in development and/or review of project schedules for every phase of the construction project lifespan by using Primavera P6;

• The Planner shall possess a degree in Civil and Structural Engineering or relevant discipline;

• The Planner shall have experience in scheduling for projects of similar scale, complexity and nature of works;

• The Planner shall possess intermediate to advanced knowledge of Microsoft Project, Excel, Power Point and Word; in addition, the Planner shall also be proficient in Primavera P6;

• The Planner shall be able to work independently, a strong team player and to handle fast paced projects;

• The Planner shall have good interpersonal, written and verbal communication skills for collaboration with stakeholders across all levels and have good presentation skills.

Job Description

• Responsible for ensuring that both CAG Employers Information

• Requirements (EIR), LTA Exchange Information Requirements (LTA EIR) and Project BIM Execution Plan (BEP) are implemented on site.

• Responsible for ensuring the capability of Contractors & sub-contractor BIM team are within the EIR documents & to the BEP.

• Responsible for ensuring that all related infrastructure and facilities are

• coordinated in BIM Model before commencement of actual works on Site.

• Responsible for ensuring that all Shop Drawings/Construction drawings are coordinated & updated in BIM Models before commencement of actual works on Site.

Job Requirements

• Minimum 10 years of relevant work experience, highly proficient in the use of BIM software and in establishing required processes and procedures and framework for BIM in projects.

• Familiar with various aspects of engineering e.g. Civil, Structural, Architecture, Mechanical, Electrical.

• Possess a Degree in Engineering / Architecture or equivalent.

• Highly motivated and able to work independently, a strong team player and able to handle fast-paced projects.

• Possess good interpersonal, written and verbal communication skills for collaboration with stakeholders across all levels and have good presentation skills.

• Shall be continuously under employment under any Consultant/Contractor for a minimum of 5 years and have successfully

• Instituted a BIM Company Deployment Plan as well as implemented Project BIM Execution Plan for at least 2 projects.

• Completed a certification course in BIM Management.

Job Description

• To plan, manage, oversee and be responsible for all aspects of the health, safety and environmental matters for the Project.

• To advise and report to the Superintending Officer and ensure the Project complies with its statutory obligations, Changi East safety requirements, airport authority's safety requirements and aerodrome safety standards.

• To manage the team of ASMs to ensure all duties and responsibilities required of them are discharged professionally and competently. He shall carry out regular meetings with the team and address any issues relating to their personal and work matters.

Job Requirements

• Minimum 10 years of Workplace Safety and Health (WSH) experience in the construction industry, preferably 5 years with developer/main contractor.

• Minimum 5 years of WSH experience in deep excavation works.

• Minimum 3 years of experience in managing a team of site safety personnel.

• Possess Engineering, Workplace Safety & Health Disciplines, or related qualifications.

• Registered with MOM as a Workplace Safety and Health Officer (WSHO) and has been practising as WSHO for at least 5 years.

• Has obtained certificate in development of a Risk Management Implementation Plan (bizSAFE Level 2) or equivalent.

• Has obtained certificate in DfS appreciation course.

• Good communication skills and a competent team leader

• Conversant with all procedures in Workplace Safety & Health Manual. To make conscious effort to be constantly updated on any subsequent revisions to the above-mentioned manuals, procedures and all applicable airport circulars

Job Description:

• Responsible for implementing all QA/QC inspection and testing, as required by specifications or by regulatory requirements and shall be familiar with all aspects of testing required for commercial building including the quality testing requirements of local Authorities such as the Standards, Productivity and Innovation Board (SPRING Singapore)
• Monitor progress and quality of all C&S, Archi, M&E and security system works, including CONQUAS, Green Mark etc to ensure compliance to project and statutory requirements
• Review procedures to improve productivity.
• Attends meetings with client, authorities, subcontractors and consultants.
• Ad-hoc duties as assigned

Requirements (Qualification & Experience):

• Preferably university graduate in Electrical/Security/Computer Engineering or IT recognised by PEB Singapore.
• Ten (10) years of relevant experience in the implementation and management of quality control systems
• Familiar with BIM for construction, Green Mark, CONQUAS and relevant authority requirements
• Full time stationed on site during construction