Job Responsibilities:

· Ensure that adequate equipment and facilities are provided for verification of product quality.

· Ensure that all controlled documents are administered effectively.

· Quality control of sub-contractors.

· Daily coordination of all site work activities on Piping, Equipment installation.

· Liaising with Client inspector/Authorized inspector to ensure project requirement is fully achieved through out the project.

· Coordinate with sub-contractor/vendor to resolve quality issues and follow up for corrective actions.

· Carry out verification of purchased products in vendor's premises as specified in contracts.

· Supervise and manage the steel welding procedure and ensure the welding quality.

· Assist on the coordination with temp QP launching sequence for whole viaduct segment.

· Ensure identification and traceability of incoming, in-process finished products.

· Stipulate and control adequate criteria for workmanship.

· Monitoring of all Inspection Records, Material Test Reports and Mill Certificates.

· Ensure that all inspection, test and identifications are carried out according to quality plan or documented procedures.

· Quality check for architectural finishing such as plastering, brick wall and etc.

· Ensure that all nonconforming materials and products are adequately controlled.

· Investigate the cause of the nonconforming products and the corrective action needed to prevent recurrence.

· Ensure that all quality reports and customers' complaints are analyzed with adequate corrective actions taken.

· Ensure that quality records are properly stored and maintained.

· Define quality requirement for service and installation of products.

· Maintain adequate statistical techniques to control product and process quality.

· Check the BCA approved drawing and study for the feasible work for site.

Job Requirements :

· Bachelor's degree in Engeering studied, or a related field

· Mininum10 years QA/QC experiences

· Able to read, understand and interpret technical requirements, quality procedures, drawings, P&ID.

· Detail-oriented and have strong communication skills and able to work with people from all levels.

· Comfortable working within a fast-changing environment, ability to multi-task and cope with ambiguity.

· Independent and a self-starter, with strong personal drive to initiate and implement.

· Good knowledge of documentation procedures.

· Hands on experience with pressure vessel, PED & MOM requirements, ENstandards

Job Responsibilities:

· Ensure that adequate equipment and facilities are provided for verification of product quality.

· Ensure that all controlled documents are administered effectively.

· Quality control of sub-contractors.

· Daily coordination of all site work activities on Piping, Equipment installation.

· Liaising with Client inspector/Authorized inspector to ensure project requirement is fully achieved through out the project.

· Coordinate with sub-contractor/vendor to resolve quality issues and follow up for corrective actions.

· Carry out verification of purchased products in vendor's premises as specified in contracts.

· Supervise and manage the steel welding procedure and ensure the welding quality.

· Assist on the coordination with temp QP launching sequence for whole viaduct segment.

· Ensure identification and traceability of incoming, in-process finished products.

· Stipulate and control adequate criteria for workmanship.

· Monitoring of all Inspection Records, Material Test Reports and Mill Certificates.

· Ensure that all inspection, test and identifications are carried out according to quality plan or documented procedures.

· Quality check for architectural finishing such as plastering, brick wall and etc.

· Ensure that all nonconforming materials and products are adequately controlled.

· Investigate the cause of the nonconforming products and the corrective action needed to prevent recurrence.

· Ensure that all quality reports and customers' complaints are analyzed with adequate corrective actions taken.

· Ensure that quality records are properly stored and maintained.

· Define quality requirement for service and installation of products.

· Maintain adequate statistical techniques to control product and process quality.

· Check the BCA approved drawing and study for the feasible work for site.

Job Requirements :

· Bachelor's degree in Engeering studied, or a related field

· Mininum10 years QA/QC experiences

· Able to read, understand and interpret technical requirements, quality procedures, drawings, P&ID.

· Detail-oriented and have strong communication skills and able to work with people from all levels.

· Comfortable working within a fast-changing environment, ability to multi-task and cope with ambiguity.

· Independent and a self-starter, with strong personal drive to initiate and implement.

· Good knowledge of documentation procedures.

· Hands on experience with pressure vessel, PED & MOM requirements, ENstandards

We are seeking an Electric System Design Engineer to design hydraulic and electric systems for Ro-Ro equipment. As a key team member, you will be responsible for developing high-performance systems that meet safety, regulatory, and operational requirements in Marine Industry. Fresh graduates from Electrical, Mechatronics, or Mechanical Engineering backgrounds are encouraged to apply, as we provide training and development opportunities to enhance your skills.

Qualifications:

• Bachelor’s degree or higher in Electrical, Mechatronics or Mechanical Engineering.
• Strong problem-solving skills and active communication skills.
• Excellent interpersonal and collaboration skills.
• Experience in the design of hydraulic and electric system add value.
• Experience in both of Shipbuilding and Marine industry will be a significant plus.

Job Description:-

1. Responsible for all aspects of drafting electrical and structural drawing of switchboard & control panels for marine and industrial use, incorporating the company's key circuit breaker products.

2. Based on abundant practical experience and extensive knowledge on circuit breakers, produce high class switchboard and control panels drawing according to company’s standard.

3. Manage and lead the project for timely and accurate production of software engineering, electrical drawing and structural drawing.

4. Based on software management skill and rich experience of programming language and software development tools, construct software for control system.

5. By communicating closely with the clients both in Singapore and Japan, responsible for accurately understanding their needs and make sure that the products delivered are perfectly designed to meet their demand.

6. During the periodic inspection of products after delivery, responsible for supervising the on-site inspection to ensure that it is carried out correctly.

7. Take the lead of investigation to solve the issue rapidly in case of any software or system issues, by closely liaising with HQ in Japan.

8. Based on the extensive knowledge of switchboard, circuit breakers and software for railway, marine, cogeneration system, power plant and biomass plant projects, liaise closely with engineers’ team in Japan HQ and clients in Singapore to ensure solutions.

Job Requirement:-

1. More than ten (10) years of experience as software and electrical design engineer in electric power system industry.

2. More than ten (10) years of experience in drawing electrical circuit and outline drawing of switchboard using AUTOCAD.

3. More than five (5) years of experience in using software programming tools for power management system in industrial cogeneration system, specifically with PLC (Omron, Fuji, Mitsubishi, Schneider product etc.).

4. More than five (5) years of experience in communicating with clients as software and/or electrical design engineer, explaining technical details to clients in an easy-to-understand manner.

5. Understand “TERASAKI” products that include circuit breaker, marine and industrial switchboard.

6. Certified as a power generation equipment specialist or equivalent and more than five (5) years of practical experience in power generation of switchboard & control products.

Skills Required:-

・Problem-solving skills in challenging and complex situations

・Project management skills from concept, prototype to implementation

・Excellent communication skill to explain technical matters to clients

・Conversant with Autocad, Software for PLC (Omron, Fuji, Mitsubishi, Schneider product).

・Certificate of 1st grade Electrical drafting specialist or equivalent

・Certificate of power generation equipment specialist

Review electrical engineering drawings and refer issues requiring changes.

Assign job tasks and work as per electrical project schedules.

Review all electrical drawings with Leadmen performing on assigned jobs to them.

Stimulate fabrication standards to ensure quality work attained from assigned staff.

Recruit, guide, train, monitor and terminate assigned employees as required.

Recommend effective solutions specified particular weight related to employment status of employees.

Schedule, assign, plan and supervise electrical shop personnel performance on different electrical projects.

Plan and prepare work and equipment usage schedule

Responsibilities:

• Attends and records the daily quality assurance related inspections for mechanical and HVAC installations
• Coordinates with other production departments, clients, and surveyors for Inspection & testing requirements
• Assigns the systems to be tested to the various supervisors and technicians involved in the operation
• Ensures that the Quality work processes to enhance efficiency and productivity
• Reports on non-conformance and issue Improvement notes, where necessary
• Ensures timely completion of project
• Ensures that all standard operating procedures comply with specifications, quality standards, statutory and regulatory requirements
• Any other assigned duties and responsibilities

Requirements:

• Degree in Marine and Offshore / Mechanical Engineering
• Minimum 5-10 years’ experience with 3 years in marine construction and installations
• Must have ASME PCC-1
• Good analytical and problem-solving skills
• Able to multi-task and able to work in a fast-paced environment

Our Addresses and Working Hours:

Seatrium (SG) Pte. Ltd.

Admiralty Yard

60 Admiralty Road West, Singapore 759947

(Transport provided from Sembawang MRT)

Mon - Thu: 8:00am - 5:15pm

Fri: 8:00am - 4:30pm

Interested candidates are invited to send us an updated resume with your current and expected salary and earliest availability.

We regret that only shortlisted candidates will be notified.

Please note that your personal data disclosed to Seatrium Limited and our group of companies, shall be used for the purposes of evaluation, and processing in accordance with our recruitment processes and policies. By providing your personal data, you have consented to the aforesaid purpose under the provisions of the Personal Data Protection Act 2012.

• Oversee daily construction activities, ensuring compliance with safety regulations, quality standards, and project specifications.
• Collaborate with architects, engineers, and other construction professionals to develop project plans and schedules.
• Monitor project expenses, track budgets, and implement cost-saving measures where possible.
• Conduct regular site inspections to ensure that construction work meets design specifications and safety standards.
• Address and resolve any issues or delays that arise during the construction process.
• Maintain accurate records of project progress, changes, and communications with stakeholders.
• Ensure all work complies with local building codes, regulations, and company policies.
• Prepare and present progress reports to project managers, clients, and other stakeholders.

Qualifications:

• Bachelor’s degree in Civil Engineering from an accredited institution.
• Preferably with atleast 2 years of experience in construction engineering or a related field.
• Proficiency in construction management software (e.g., Procore, Buildertrend)
• Strong understanding of construction methods, materials, and legal regulations.
• Excellent problem-solving and analytical skills.
• Effective communication and leadership abilities.

Job Summary:

• As a Service Engineer, you will play a critical role in maintaining the operational efficiency of our equipment.
• Your expertise will ensure that our services remain top-notch, directly impacting our client satisfaction and operational success.

Key Responsibilities:

• Conduct periodic inspections, repair, service and maintenance of Musasino equipment to ensure reliable operation.
• Collaborate with clients and superintendents to deliver quality services efficiently.
• Generate reports and present findings to relevant personnel.
• Provide remote troubleshooting support through emails, ensuring customer issues are resolved promptly to maintain high satisfaction levels.

Job Requirements:

• Fresher or related marine engineer experience are welcome.
• A minimum of a Diploma in Engineering (Electrical, Electronics, Mechanical, Mechatronics) or equivalent educational background.
• Ability to work overtime and weekends when required.
• Willingness to travel overseas for an assignment as required.
• Ability to work independently and under pressure, delivering quality results within tight schedules.
• Team player.

Highlights:

• Gross Salary: S$3000 to S$4000/ month
• Working Day: 5 days
• Working Hour: 8am to 5pm
• Overtime paid when working outside of working hours (include Weekend/ Public Holiday)
• Dental and Medical Benefits
• AWS

Job Description

• Prepare and review the design of the Mechanical Works, such as piping & equipment drawings, calculation and data sheets
• Involve in daily coordination with internal C&S and BIM team to resolve all the clashes, penetration etc
• Develop the work schedule and coordination of the project works to ensure project is on schedule
• Attend to FAT, supervision of the delivery, installation and testing and commissioning of mechanical works
• Handle and resolve all site technical relating matters
• Prepare, review and assist in subcontractor design and submission, ensuring all project specifications and design standards are met
• Prepare all relevant checklist for Installation and Testing & Commissioning Works
• Assist and collaborate with other project team members to comply with project requirements and meet project schedules
• Collaborate with internal stakeholders, clients, consultants, vendors and contractors
• Attend to clients’ comments and ensure clients’ approval & acceptance to all Mechanical Works related design, installation and Testing & Commissioning Works

Requirements

• Min degree in Mechanical Engineering
• 5 to 8 years of relevant experience in the construction industry. Working experience in water or wastewater industry will be an advantage
• Familiar with Auto CAD, Mechanical, Structure drawings and Microsoft Office
• Experience in design, installation, testing and commissioning of the mechanical works e.g. pipings, pumps etc
• Experience in Project Execution, Project Coordination, Supervising and Coordination with sub-contractors, consultant, and Client
• Good technical knowledge in understanding the Mechanical System
• Well versed in BIM software i.e. Bentley and Navisworks
• Team player with good interpersonal skills
• Meticulous and analytical with excellent problem-solving skills
• Highly motivated and able to work independently with minimal supervision

Job Description

• Interpret contract specifications, architectural standards, and designs for construction
• Organise and lead meetings for design and construction; monitor and manage budgets; write reports; and carry out additional administrative duties associated with the projects that are allocated
• Oversee architectural planning, consulting coordination, and document control, including tracking sample submissions and drawing approval status
• Coordinate, organise and prepare construction and architectural documents and drawings
• Oversee architectural projects, communicate with clients and subcontractors regarding architectural issues, and guarantee the highest levels of architectural workmanship
• Provide the architectural designers with technical guidance on building requirements
• Organize and/or participate in subcontractor and consultant meetings

Requirements

• Min diploma in engineering
• Min 3 years of construction experience

Stork Gears & Services Asia Pte Ltd are an ISP for Rotating equipment from Europe which focuses mainly on Inspections, Repairs, Modifications and Overhaul of Gearboxes for both the Marine and Land based Applications. We have an OEM background, Rademakers, Conrad, Brevo, Kuypers, Jahnel Kesterman, but with an Independent service provider mind-set.

Stork is known for:

• Highly qualified and experienced engineers
• Highly Price competitive vs OEM
• In-house manufacturing critical parts
• On-site reverse engineering

Our service portfolio consists of:

• Diagnostics services
• Onsite services 24/7
• In-house engineering: design of gearboxes,
• Parts manufacturing (Impellors, shafts, gears)
• Custom built
• Workshop repair

Job description: (Field) Service Engineer

Purpose of the job

Responsible for the technical realization of projects, during the disassembly, assembly, inspection and repair, installation and commissioning of equipment, installations and related components.

Characterization

• Performs assignments/projects on the basis of requests from the project manager and project planning.
• Technical lead of the project team consisting of mechanics, (field) service engineers and subcontracted staff.
• Is responsible for maintaining the overview and ensures that the project is executed safely, in a structured manner, with a high quality standard and within planning and budget.
• Projects are performed at client sites (worldwide) or in the workshop. Often under time pressure and in unexpected or hectic circumstances.
• Flexibility: reachable and deployable, also on irregular hours.
• Realizes the most optimal technical solution and report on progress and the (technical) end result to the customer.
• Fulfills a leading role in respect of compliance with safety and environmental instructions, guidelines and policies of Stork and the client.
• Is highly specialized in installation & equipment technology and product knowledge.
• Service—oriented professional.

Tasks/Responsibilities

1. Authorizations

• Independently performing inspections, measurements, repairs, disassembly and assembly of installations, equipment and related components.
• Authorized to operate specialist machines and tools.
• Competent to specialist work based on required training.

2. Execution

• (dis)Assembly, inspection and repair of installations, equipment, related components and connected installations onsite, according to work instructions. Sets priorities on location and specific approach to the work; on site troubleshooting.
• Searches for the technical optimal solution with regard to costs and downtime.
• Responsible for the overview of the progress of the project on-site, ensuring that the project is carried out safely, in a structured manner, with a high quality standard and within planning and budget.
• Communicating the status and progress of the project to the project manager, adequately reporting possible scope changes.
• Self-starting and able to fully prepare, execute and complete the work independently both technically and administratively.
• Can deal very well with tight deadlines and can very well structure work in hectic and/or unexpected circumstances.
• Makes adequate protocols (if necessary) and technical reports.
• Works closely with other relevant departments so that the project can be delivered to the customer in accordance with the scope.
• Monitor and manage technical intellectual property if appropriate.
• Technical assistance and advice to internal and external stakeholders on use, maintenance, repairs, risks and possibly renewal of the installation.

3. Leading the team

• Managing the project team (on-site), ensuring that the project is carried out safely, in the agreed manner, with high quality and within the agreed timeframe.
• Detection of deviations, intervening if a deviation is detected.
• Coaching, supporting and guiding the project team on-site.
• Responsible for timely and adequate internal and external reporting and administration.
• Making and/or supervising correct use of: tools, machines, measuring instruments and other means of production.
• Maintaining equipment in good condition under applicable norms and regulations, timely reporting and/or solving in case of imperfections and malfunctions.
• Proactive in personal development and knowledge sharing within the team and organization.

4. Safety, quality and environment

• Is accountable for safety and quality aspects within the project.
• Meeting and monitoring the correct safety measures for a safe working environment.
• Report safety incidents and / or near misses in accordance with applicable procedure.

5. Others

• Responsible for maintaining contact with the client at an operational level.
• Actively participate in realization of additional work during development and execution of projects, technically assisting the sales department.
• Proactive relationship management; as ambassador encourage clients to purchase more services and / or products.
• Keeps knowledge up to date within his area of expertise (i.e. through keeping track of technological developments and/or professional literature).
• Assists in development of and test new methods, techniques and new services.

Knowledge and Skills

• Relevant technical education, i.e. mechanical engineering
• Relevant technical education; mechanical engineering or related
• Preferably services background
• Possesses required certifications
• Able to read schedules and mechanical engineering drawings
• Use and application of auxiliary tools and measuring instruments
• Fluent in English

Responsibilities:

• Understand Contract Specification.
• Understand Marine Class and Regulatory Requirement, Piping, Special Item and Valve Material Specification.
• Understand P&ID and Piping routines.
• Good knowledge in preparing Technical specification and Material take off (MTO).
• Review and comments technical proposal from vendor.
• Technical Bid Evaluation for procurement.
• Monitor procurement process to meet Project Schedule.
• Review vendor certified Document (VCD).
• Monitor piping bulk material usage, surplus material and warehouse balance utilisation.
• Interface with vendor, other discipline lead, procurement, production, commissioning.
• Attend factory acceptance test (FAT) if required.
• Able to perform piping procurement related activities with no or minimum supervision.

Requirements

• Prefer to have at least 5 years of piping engineering related working experience or similar activities as describe above.
• Prefer to have experience in Offshore/Shipyard project, Rig building/Ship building.
• Prefer to have experience in FPSO project, both topsides & marine.

Our Addresses and Working Hours:

Seatrium (SG) Pte. Ltd.

(Tuas Boulevard Yard)

80 Tuas South Boulevard, Singapore 637051

(Islandwide transport provided)

Mon - Thu: 8:00am - 5:15pm

Fri: 8:00am - 4:30pm

Interested candidates are invited to send us an updated resume with your current and expected salary and earliest availability. We regret that only shortlisted candidates will be notified.

Please note that your personal data disclosed to Seatrium Limited and our group of companies, shall be used for the purposes of evaluation, and processing in accordance with our recruitment processes and policies.

By providing your personal data, you have consented to the aforesaid purpose under the provisions of the Personal Data Protection Act 2012.

Responsibilities:

• Understand contract and scope of work (i.e. SOW) and extracting the contract requirement into the checklist.
• Follow up FEED, P&IDs developed by consultant.
• Able to perform equipment sizing for pump required flow rate and pumping head together with NPSH verification.
• Able to perform piping line sizing.
• Able to develop system UFD/PFD.
• Able to create System Process Data Sheet.
• Develop/Update FPSO Hull common system related Topside, Safety, Hull marine systems in P&ID.
• Well understanding of common Class requirement such as ABS, LR and DNV Rules for marine system design.
• Well understanding of Equipment Isolation Philosophy and Specification from client.
• Well understanding of common piping material selection and application for marine system design as reference to International Standard.
• Able to incorporate the recommendations from the safety studies into the P&IDs and other relevant documents
• Able to review/comments technical proposal and vendor certified documents (VCD) from vendor (i.e. control valves specifications, PSVs specifications, etc.)
• Liaise with other discipline for relevant information that are needed for process design.
• Able to understand safety related drawing & documents (e.g. Safety Plan, Area Classification, Safety Signaling, Technical Specification for safety equipments, HSE Manual, Hydrant Location Study etc).
• Understand P&IDs and other related process, safety & instrumentation items
• Well understanding of the galvanic corrosion phenomena in the system design and able to avoid or resolve the galvanic corrosion related problems.
• Define control narrative and alarm set point for the instruments.
• System descriptions & all other kind of OIM (operation & maintenance manual)
• Sizing calculations (i.e. PSVs calculation, BDV calculations, SDV calculation, Control valves calculation).
• Carry out Hull Process related studies and prepare official report.
• Good knowledge in process simulation (PRO-II / HYSYS process simulator)
• Familiar System Design Safe Chart, Cause & Effect Matrix, Narrative Control Logic.
• Having knowledge to evaluate the relevant safety studies in FPSO design (i.e. HAZOP, HAZID, Radiation Study, Fire Explosion Study).
• Understanding of Working Environment Requirement and Human Ergonomic Design.
• Support commissioning activities and troubleshooting of system performance related issues.

Requirements:

• Prefer to have at least 5 years of Hull Process engineering related working experience or similar activities as describe above.
• Prefer to have experience in FPSO project, both topsides & marine.
• Prefer to have experience in Offshore/Shipyard project, Rig building/Ship building.

Our Addresses and Working Hours:

Seatrium (SG) Pte. Ltd.

(Tuas Boulevard Yard)

80 Tuas South Boulevard, Singapore 637051

(Islandwide transport provided)

Mon - Thu: 8.00am - 5:15pm

Fri: 8.00am - 4:30pm

Interested candidates are invited to send us an updated resume with your current and expected salary and earliest availability. We regret that only shortlisted candidates will be notified.

Please note that your personal data disclosed to Seatrium Limited and our group of companies, shall be used for the purposes of evaluation, and processing in accordance with our recruitment processes and policies. By providing your personal data, you have consented to the aforesaid purpose under the provisions of the Personal Data Protection Act 2012.

Job Description

• Oversee process mechanical design for process plant (Wastewater Treatment Plant, Water Treatment Plant, etc) including P&ID, equipment/piping/valve sizing, equipment selection, equipment/piping layout, equipment specification/data sheet, etc
• Provide process mechanical input and coordinate with other disciplines (including the BIM modelling team) for the design, installation and T&C work
• Oversee technical review of mechanical equipment/system vendors’ proposal and submission during procurement, detailed design and installation stages, support the procurement and tender work
• Prepare the process mechanical submissions and resubmissions to project consultants and client according to project schedule and clear the submittal comments
• Manage the mechanical equipment suppliers / subcontractors to meet the project schedule and quality requirements for design, installation and testing & commissioning
• Support on the testing, commissioning and O&M work

Requirements

• Minimum bachelor’s degree in chemical/environmental/mechanical engineering
• Minimum 4 Years’ experience in process/mechanical work (design, engineering, installation support, T&C, etc.), ideally for water/wastewater treatment project (including sludge treatment); For senior position, candidate must have at least 8 years of relevant experience.
• Familiarity with international and local standards (e.g., ASME, ANSI, PUB Singapore regulations)
• Familiarity with mechanical equipment used in WWTPs, including such as screens, pumps, mixers, blower, air compressors, tanks, biogas equipment, odour control system, sludge equipment, piping, and valves, etc
• Must be a self-starter and be able to work with minimal supervision, make sound decisions, take independent action, and provide focused solutions to assigned projects
• Possess strong inter-personal and communication skills and be able to work well with people at all levels in the organization
• Must have advanced computer literacy in commonly usedsoftware applications such as MS Office
• Knowledge in Naviswork and Bentley View Software will be an added advantage

The Senior Engineer, Projects, will lead and manage projects from initiation to completion, ensuring alignment with scope, budget, and timeline requirements. This role involves overseeing mechanical and electrical components' fabrication, assembly, and installation while coordinating with cross-functional teams to meet project objectives.

Responsibilities

• Lead projects, ensuring timely delivery, adherence to scope, and budget compliance.
• Oversee fabrication, assembly, and installation of mechanical and electrical components.
• Coordinate with factories, contractors, and cross-functional teams to align objectives.
• Review and interpret mechanical drawings, specifications, and technical data.
• Ensure fabrication adheres to layouts and designs.
• Collaborate with the procurement team to ensure timely material delivery.
• Conduct quality checks, testing, and inspections to maintain standards.
• Resolve technical issues and implement corrective actions.
• Planned and coordinated with after-sales teams to ensure smooth workflows.
• Maintain project documentation, including progress reports, Gantt charts, and technical records.
• Supervise inbound and outbound activities.
• Inspect parts to ensure compliance with BOM and data sheets.

Requirements

• Degree or Diploma in Mechanical Engineering or related field.
• 5-7 years in a similar role or industry.
• Proficiency in AutoCAD, Microsoft Office Suite, and project management tools.
• Knowledge of mechanical systems, equipment, and industry standards.
• Strong analytical and decision-making abilities.
• Ability to manage multiple projects simultaneously.
• Detail-oriented with excellent problem-solving skills.
• Strong communication and coordination abilities.
• Preferred candidates should have access to a vehicle.

Job Responsibilites

• Prepare Master Program and update progress monthly.
• Prepare Progress forecast of rolling programs and update of resources.
• Resolve any instrumentation issues & recording.
• Coordinate with services department about diversion work and schedule.
• Ensure overall site progress are updated according to schedule.
• Prepare monthly progress report for client/consultants.
• Assist Project Manager in the preparation and submission of verified work done to Quantity Surveyor.
• Any other adhoc duties as assigned by management.

Job Requirements

• Possess a Degree Civil Engineering and above or equivalent.
• At least 5 years of experience in construction planning and programme coordination for railway projects.
• Computer literate with proficiency in planning software such as Microsoft Project, AutoCAD, P6 Primavera.
• Experience in LTA Projects will be advantage.
• Willing to be based at project site office and work 5.5 days.

Job Responsibilities:

- Perform basic and advanced machine electrical wiring works

- Develop electrical testing jigs and perform testing and validation of machines

- Lead the production team to strictly adhere to production schedule and same time improving the manufacturing process to improve quality, cost, and productivity.

- Creates, implements, and monitors KPI indicators on product quality and section capability

- Provide shop floor feedback to Production Engineering and D&D Department

- Assist the Production Manager to provide quality, cost effective and efficient support for launching of new machine models

- Perform machine pre & post machine power ON inspection checks, machine parameter settings, testing and inspection according to standard

- Able to troubleshoot and resolve machine electrical non conformance

- Perform machine final electrical inspection and adjustments for any defects to maintain high level of quality

- Prepare reports on productivity, quality, claims, etc

- Work with engineering and other departments to improve assembly processes

- Monitor the serviceability of measuring electrical instruments or jigs and fixtures and reporting to Supervisor or Manager any non-compliance condition

- Maintain accurate records of inspection result at each electrical process

Job Requirements:

- Minimum Diploma or equivalent in Electrical required

- 2-3 years working in a machine assembly environment

- A good track record of supporting the department achieving KPI

- Strong understanding of 5S and HSE knowledge

- Able to work effectively in a fast and ever-changing stressful environment

- Maintain good Quality standards, 5S and safety discipline

- Well verse in Microsoft office (Excel, Words, Powerpoint and Outlook)

- Knowledge of drawing software(Solidworks, Unigraphic, etc) is added advantage

Job Description

- Work with Production Engineers, Supervisors and Technician to design, develop, and improve engineering processes.

- Planning and coordinating of production schedule and production output.

- Plan and implement improvement projects for productivity improvement

- Ensuring all monthly operating expenses stay within allocated budget.

- Support inspections of equipment and scheduling maintenance or repairs with Maintenance Dept

- Inspecting inventory and reporting inconsistencies as well as ordering more materials.

- Producing CAD drawings, nesting thru company smart system according to our standard specifications.

- Evaluating first article and processes and ensuring standardization of quality assurance measures.

- Calibrating and troubleshooting of equipment /machines as required.

- Perform time study and improve standard time hour

Job Requirements:

- A degree or minimum diploma in Engineering discipline.

- Minimum 2 years' experience in precision engineering in manufacturing industry

- Proficient in 3D drawing software – Solidworks

- Proficient in Microsoft Office

- Familiar with manufacturing quality assurance techniques

- Understand 5S discipline, TQC and other quality improvement tools

- Good interpersonal skills, problem-solving and project management skills

We are looking to hire a Senior Process Engineer to work on projects in the Pharmaceutical and Biopharmaceutical sectors.

Key responsibilities:

• Design of process and utilities – preparation of PFDs, P&IDs, equipment sizing calculations
• Coordination of design with other design disciplines and equipment suppliers
• Ownership of equipment modules and packages through design and procurement phases
• Completion of Design Risk Assessments
• Participation in Technical and Safety reviews
• Interfacing with client design team/end users
• Process optimization/site support

Requirements

• Degree in Chemical/Process Engineering (or equivalent)
• At least 8 years of design and project experience in the Pharmaceutical and Biopharmaceutical sectors.

What you can expect

• The opportunity to work on a range of projects, from conceptual stage through to detailed design, commissioning and qualification.
• Career enhancement due to the wide scope of the projects and experience you will receive.
• Work closely with Industry leaders

Responsibilities:

• Prepare detailed cost breakdown as per the scope including detailed material take off, activity wise resource requirements, subcontractors, indirect costs, etc
• Communicate with purchase dept & suppliers to get competitive quote for materials by negotiation
• Liaise with internal departments (Sales, QA/QC, Production and Purchase) to collect project information & data
• Prepare technical proposal including statement with estimated cost in time.

Requirements:

• Diploma or Degree in Mechanical Engineering or related discipline, with minimum 2 years’ cost estimation experience in the Oil and Gas, Petrochemical/Chemical industries, handling similar products is an advantage
• Experience in preparing proposals/tendering preferred
• Fresh graduates are also welcome to apply
• Good application knowledge of MS Office
• Strong communication and negotiation skills
• Only Singaporeans or Singapore PR need to apply

Meranti Power Pte Ltd, a fully owned subsidiary of Energy Market Authority, is currently in the final phase of power generating station development. and will thereafter, operate and maintain the power generating station. We are inviting applicants for the position of Senior Engineer, Electrical who shall report to the Head, Electrical. The scope and requirements are as follows:

RESPONSIBILITIES :

A. Current & future Project

• Ensure compliance to the prevailing Workplace Safety and Health Act and all relevant authorities’ regulations.
• Assist the Project Director and Head (Electrical) in all phases of Project Cycle related to all electrical systems and equipment including conceptual stage, drafting work scope for Owner’s Engineer consultant, system design and engineering stage, execution stage and right up to commissioning.
• Work with the Consultants for the timely completion and cost-effective implementation of the projects.
• Participate in the design review, implementation & commissioning of new power plants’ Electrical systems, including evaluation and recommendations for acceptance of the Consultants/Contractors’ Electrical systems engineering design and selection, procurement, and installation proposals for the power plant to ensure successful commissioning on time & within budget.
• Detect and provide prompt triggering of risks or potential risks to avoid/minimize delays or losses, recommend cost effective plans and monitor finances to ensure each phase of Electrical system works is started and completed on time and within the budget allotted.
• Attend meetings with various stakeholder to report on project progress against milestones and challenges faced
• Manage problems resolution processes with Head (Electrical) and consultants with respect to power plant project Electrical systems design, implementation, installation, and commissioning and resolve co-ordination/interfacing issues with other parties.
• Provide status updates to Head (Electrical) for report to MP’s Senior Management on progress of major Electrical systems project activity against the schedule, highlighting significant milestones and any issues/interfacing affecting or may affect project cost and schedule.
• Support Head (Electrical) to communicate, coordinate and collaborate with Contractor, external parties and agencies (SPPG, EMA/ PSO, JTC, etc) with regards to Meranti Power’s 400kV Switchhouse/ Substation, SPPG feeder connections, Gas Insulated Switchgears, Generator Step-up Transformer, Insulated Phase Bus Duct, etc. at different stages of the project (including Commissioning).

B. Operation & Maintenance Phase

• Be familiar with all regulations pertaining to the Electrical systems of the power station’s equipment, auxiliaries and common systems maintenance works and safety, e.g. Workplace, Safety & Health Act’s Regulations, including Risk Assessment and Mitigating Measures, Work Methods, Permit-to Work, Lock-Out-Tag-Out System in relation to maintenance of Electrical equipment in the power generation station.
• Prepare technical specifications for equipment electrical parts and work services when required. Work with Procurement to manage the procurement of Electrical parts and services.
• Coordinate all Electrical Maintenance programmes (Predictive, Preventive, Corrective) and liaising with relevant stakeholders to ensure safe and timely completion of works.
• Be familiar with Predictive Maintenance monitoring techniques.
• Familiar with use of Computerised Maintenance Management System (CMMS).
• Manage and optimize all planned plant/equipment electrical maintenance activities during minor and major overhauls and inspections
• Responsible for the functional tests and analyse the failures related to Electrical systems and components and recommends remedial/mitigation measures to prevent recurrence. Troubleshooting of faults/defects & carry out failure analysis to determine root cause.
• Study, evaluate and implement plant improvement projects to enhance overall plant reliability, availability and performance
• Supervision of Electrical maintenance contract works and prepare work procedures and risk assessment for all Electrical maintenance activities
• Manage day-to-day activities of Electrical team effectively; may be appointed as Reporting Officer to technical officers.
• Support Head (Electrical) to engage and manage Licensed Electrical Worker (LEW), Qualified Persons (QP), Competent Persons (CP) to carry out the required services and works.
• Track the year-to-date expenditure against the approved department Electrical budget; Support Head (Electrical) to prepare upcoming budgets.
• Prepare Department’s Electrical monthly report
• Design, coordinate and conduct training on Electrical matters

C. Other tasks

• Perform administrative tasks for the benefit of the organization as instructed by Head (Electrical) or Senior management e.g. secretariat for meetings, staffing duties, presentations, etc.
• Take part in organisation-wide activities in various capacities such as organising committees for events,
• Attend training/ events/ conferences that is in line with the organisation objectives and proceed to share the learning points for organisation benefit

REQUIREMENTS :

• Degree in Electrical Engineering or equivalent.
• Major Project Management experience with at least 3 years in power plants development, implementation, commissioning tests, preferably including operation/electrical maintenance of large power plants, specifically employing Combined Cycle Technology.
• Conversant with international and local codes, standards and recommended practices for design and selection of electrical equipment related to the above plants will be an added advantage.
• Hands-on experience in power plant projects’ tender preparation including technical/functional and commissioning tests specifications for C&I equipment, tender evaluations, contract negotiations, contract administration and contract supervision.
• Experience in overseeing the power plants worksite’s adherence to Workplace Safety & Health, and relevant regulatory requirements.
• Will be required to work beyond office hours in event of plant exigency or emergency.
• Self-motivated, results focused and willing to work under tight schedules with multi-disciplinary teams.
• Able to lead a technical team and harness and direct the strengths of the different members to output greater effect than the sum of each individual. ·
• Willing to work in construction site office during construction stage and Jurong Island. (Morning transportation pick-up points available at different parts of Singapore.)

Only shortlisted candidates will be notified.

By submitting your personal data and/or resume to Meranti Power Pte. Ltd. (“MP”), you shall be deemed to have given your consent to MP for collecting, using, and disclosing your personal data for the purpose of assessing your job application.

Responsibilities:

• Responsible to contribute to product cost savings through identifying opportunities for cost savings & build value engineering project pipeline
• Develop methodologies, templates and approach for target costs based on product analysis data
• Analyze and evaluate design for materials, manufacturing process & supply chain for value analysis / value engineering opportunities
• Execute & drive VAVE projects starting from Idea generation to implementation
• Co-ordinate with Global & local stake holders including suppliers for project execution including samples, prototypes and testing requirements
• Build active VAVE project funnel and build active VAVE project funnel and todDrive multiple VAVE projects in a timely manner to support business goal target
• Establish and update processes for execution on teardown, benchmarking and VAVE requests

Requirements:

• At least 5 years of working experience in the EMS or an MNC environment
• Strong analysis skills, knowledge in material pricing and strategy
• Strong knowledge in Mechanical/Electro-Mechanical/Electronics commodities

Interested candidates are to submit a detailed resume to speed up the application process.

We regret to inform that only shortlisted candidates will be notified.

Thank you for applying.

• Manage & develop new customers based for service sales in the industrial, Marine & Offshore/Oil Gas market.
• Responsible for maintaining a high standard level of customer services and good customer relation.
• Responsible for maximizing a high level of profit margin and ensure meeting the pre-set sales target.
• To identifying and developing sales & marketing strategies to exhaust opportunities in the local market as well as to exploit overseas markets.
• Make sales presentation and provide technical support to customer
• Gather information on market demand, competition and latest technologies.
• Submission of weekly, monthly and quarterly reports.

· Report to Project Director / Project Manager.

· Attend site visit and prepare cost estimation.

· Co-ordinating and follow up all the individual respective project team like Civil, E&I, Scaffolding, Automation, Passivation, Safety, Lifting and others.

· As a Controls Engineer you should perform a vital role in designing and developing systems for manufacturing operations.

· Draft tender documents and cost estimation spreadsheet.

· Design layouts, materials and information flow, or machine placement.

· You should responsible to evaluating performance and proposing and implementing improvements new or existing systems.

· Present final figures and unit rates to management.

· Submit tender documents and attend clarification meeting (if requested by client).

· Attend project/ safety meeting with client/sub-contractor/internal and prepare minutes of meeting.

· Prepare overall construction detail schedule for the project.

· Plan, coordinate and execute the job to meet the schedule and quality requirements.

· Prepare / review of project specification, P&ID and material take-off.

· Handling all technical queries and investigating all work-related problems and coordinating with client/sub-contractor/supplier to clarify the problems.

· Ensure the Safety, Productivity and Quality of the project.

· Prepare Method of Statement (MOS), Inspection Test Plan (ITP), Project Schedule and other working procedures.

· Ensure the installation / erection works meets the specification and requirements.

· Liaise with QA/QC personnel and ensure all the works comply with the requirements.

· To carry out inspecting and rectifying any unsafe practices and unsafe place of work.

· You will oversee the safety and job/ project operation.

· Prepare weekly / monthly progress reports/ safety reports/ manpower reports etc.

· You are to direct, guide and manage all tasks under your charge and ensure it is carried out in the most creative, efficient and professional manner to the best of your ability.

· You shall ensure, uphold and comply with all office standards, local by-laws and regulatory requirements.

Job Description & Responsibilities:

Reporting directly to the Assistant Project Manager, Project Manager, Senior Project Engineer is responsible for the following:

• Lead and manage project supervisors to ensure the successful completion of projects.
• Ensure adherence to project budgets, schedules, and scope of work, while deploying appropriate staff resources.
• Review and assess project drawings, plans, specifications, and other relevant documents.
• Identify and troubleshoot issues arising during project execution and implement timely resolutions.
• Conduct and actively participate in weekly site meetings to monitor project progress.
• Collaborate with the Safety Officer to ensure compliance with quality standards and health & safety regulations.
• Monitor site staff to ensure strict adherence to all safety regulations.
• Strong analytical and problem-solving skills, resourceful and meticulous;
• Highly motivated and pro-active with the ability to work both independently as well as in a team;
• Perform night work based on project needs.
• Prepare and submit project reports in a timely manner.
• Develop project drawings, including as-built drawings and shop drawings, as required.
• Perform any other tasks as assigned by the Assistant Project Manager, Project Manager.

Knowledge/ Skills/ Abilities:

• Knowledge of building and structural details, working drawings and local construction practices.
• Knowledge of local regulations and engineering standards.
• Good verbal and written communication skills.
• Good organizational and interpersonal skills.
• Able to work independently and as a team.
• Good time management skills with exceptional attention to detail and ability to manage multiple tasks/ projects at one time.
• Familiar with tender and bidding processes.
• Familiar with local regulations pertaining to building, construction and safety.

Requirements:

· Diploma/Bachelor’s degree in Electrical Engineering or related field.

• Proficient in Microsoft Office (Outlook, Word, Excel and PowerPoint) for Windows.
• Ability to work with flexibility to work long hours when necessary.

· Minimum 5 years of experience in electrical engineering, in Residential/Industrial/Commercial and/ and other types of buildings and/or construction.

• Certification in BCSS (Building Construction Supervisor Safety) or higher safety certification.

· Proficiency in electrical design software (AutoCAD, Revit, Navisworks,BIM360, ACC), strong knowledge of electrical codes and standards, excellent problem-solving and communication skills.